Pioneer DEH-X7550SD, Owner'S Manual

Page: 5 / 156

Use and care of the remote
control
Using the remote control
1
Point the remote control in the direction of the
front panel to operate.
When using for the first time, pull out the film
protruding from the tray.
Replacing the battery
1
Slide the tray out on the back of the remote
control.
2
Insert the battery with the plus (+) and minus
(
–
) poles aligned properly.
WARNING
!
Keep the battery out of the reach of children.
Should the battery be swallowed, consult a
doctor immediately.
!
Batteries (battery pack or batteries installed)
must not be exposed to excessive heat such
as sunshine, fire or the like.
CAUTION
!
Use one CR2025 (3 V) lithium battery.
!
Remove the battery if the remote control is
not used for a month or longer.
!
There is a danger of explosion if the battery is
incorrectly replaced. Replace only with the
same or equivalent type.
!
Do not handle the battery with metallic tools.
!
Do not store the battery with metallic ob-
jects.
!
If the battery leaks, wipe the remote control
completely clean and install a new battery.
!
When disposing of used batteries, comply
with governmental regulations or environ-
mental public institutions
’
rules that apply in
your country/area.
Important
!
Do not store the remote control in high tem-
peratures or direct sunlight.
!
The remote control may not function properly
in direct sunlight.
!
Do not let the remote control fall onto the
floor, where it may become jammed under
the brake or accelerator pedal.
Frequently used menu
operations
Returning to the previous display
Returning to the previous list/category (the folder/
category one level higher)
1
Press / DISP .
Returning to the ordinary display
1
Press BAND / .
Returning to the ordinary display from the list/cat-
egory
1
Press BAND / .
Selecting a function or list
1
Turn M.C. or LEVER .
!
In this manual,
“
Turn M.C.
”
is used to describe
the operation used to select a function or list.
Tuner
Basic operations
a 8 9
1 4 6 7 5 23
RDS
b 8
1 4 6 7 5 23
Non-RDS or AM
1 Band indicator
2 News
indicator
3
Traffic Announce indicator
4
5
(stereo) indicator
5 Preset number indicator
6 LOC indicator
Appears when local seek tuning is on.
7
Signal level indicator
8
TEXT indicator
Shows when the radio text is received.
9 PTY label indicator
a
Program service name
b
Frequency indicator
Selecting a band
1
Press BAND / until the desired band ( FM-1 ,
FM-2
,
FM-3
for FM or
AM
) is displayed.
Manual tuning (step by step)
1
Turn
LEVER
.
!
Select Manual (manual tuning) under Tuning
Mode to use this function. For details about
the settings, refer to Tuning Mode (LEVER tun-
ing setting) on page 7.
Switching preset stations
1
Turn LEVER .
!
Select
Preset
(preset channel) under
Tuning
Mode
to use this function. For details about
the settings, refer to Tuning Mode (LEVER tun-
ing setting) on page 7.
Seeking
1
Turn and hold down LEVER .
!
While turning and holding down LEVER ,
you can skip stations. Seek tuning starts
as soon as you release
LEVER
.
Using PI Seek
If the tuner cannot find a suitable station, or the
reception status deteriorates, the unit automati-
cally searches for a different station with the
same programming. During the search,
PI SEEK
is displayed and the sound is muted.
Using Auto PI Seek for preset
stations
When preset stations cannot be recalled, the
unit can be set to perform PI Seek during preset
recall.
!
The default setting for Auto PI Seek is off.
Refer to
Auto PI (auto PI seek) on page 16.
English
Using this unit
5
Section
Using this unit
En
02