En
12
Mixer section
c
d
4
4
e
g
f
h i
j
b
1 2
1 2
1 2
1 2
5
3
9
7
4
6
a
5
5
5
3
9
4
6
a
8
7
8
1
FX 1 assign button
Turns effect unit FX1 on and off for the respective channel.
2
FX 2 assign button
Turns effect unit FX2 on and off for the respective channel.
3
TRIM control
Adjusts the individual channel output gain.
4
EQ (HI, MID, LOW) controls
Boosts or cuts frequencies for the different channels.
5
Channel Level Indicator
Displays the sound level of the respective channels before passing through the
channel faders.
6
COLOR control
This changes the parameters of the SOUND COLOR FX of the different channels.
7
Headphones CUE/MIC TALK OVER button
Press:
The sound of channels for which the headphones [
CUE
] button is pressed is
output to the headphones.
!
When the headphones [
CUE
] button is pressed again, monitoring is
canceled.
When the [
INPUT SELECT
] switch for channel 3 or 4 is set to [
MIC1
] or [
MIC2
],
the talkover function can be turned on or off.
When the talkover function is on, the headphones [
CUE
/
MIC TALK OVER
] but-
ton flashes. When a sound of over –15 dB is input to the microphone, the sound
other than that of the microphone is attenuated by approximately 20 dB.
!
The talkover function for both the microphone connected to the [
MIC1
] ter-
minal and the microphone connected to the [
MIC2
] terminal can be turned
on and off by pressing the headphones [
CUE
/
MIC TALK OVER
] button for
either channel 3 or channel 4.
[
SHIFT
] + press:
The track’s tempo can be set by tapping the button. (Tap function)
8
Headphones CUE button
Press:
The sound of channels for which the headphones [
CUE
] button is pressed is
output to the headphones.
!
When the headphones [
CUE
] button is pressed again, monitoring is
canceled.
[
SHIFT
] + press:
The track’s tempo can be set by tapping the button. (Tap function)
9
Channel fader
Move:
Adjusts the level of audio signals output in each channel.
[
SHIFT
] + move:
Use the channel fader start function.
=
Using the channel fader start function
(p. 22 )
a
Crossfader Assign Switch
Assigns the channel output to the crossfader.
[
A
]: Assigns to [
A
] (left) of the crossfader.
[
B
]: Assigns to [
B
] (right) of the crossfader.
[
THRU
]: Selects this when you do not want to use the crossfader. (The signals do
not pass through the crossfader.)
!
If microphone sound is selected using the [
INPUT SELECT
] switch of chan-
nel 3 or channel 4, even through the crossfader assign switch is switched,
the sound of that channel cannot be assigned to the crossfader.
b
Crossfader
Outputs the sound assigned with the crossfader assign switch.
[
SHIFT
] + move:
Uses the crossfader start function.
=
Using the crossfader start function
(p. 22 )
c
MASTER LEVEL control
Adjusts the master sound level output.
d
Master level indicator
Displays the master output’s audio level.
e
BOOTH MONITOR LEVEL control
Adjusts the level of audio signals output from the [
BOOTH OUT
] terminal.
f
SOUND COLOR FX buttons
Turns
SOUND COLOR FX
on and off.
g
MASTER CUE button
Turns monitoring of the master output’s sound on and off.
h
SAMPLER SYNC button
Synchronizes the sampler deck’s tempo with the master deck’s tempo.
!
Only a sampler slot with the PLAY mode set to [
Loop
] synchronizes the
tempo with the master deck’s tempo.
[
SHIFT
] + press:
Sets the sampler deck as the master for synchronization.
i
SAMPLER CUE button
Turns monitoring of the sampler deck’s sound on or off.
[
SHIFT
] + press:
Sets the sampler deck’s tempo by tapping the button.
!
Only a sampler slot with the PLAY mode set to [
Loop
] will be the same tempo
as the BPM value on the sampler panel.
j
SAMPLER VOLUME fader
Adjusts the sampler’s overall sound level.
