manualshive.com logo in svg

Pioneer CB-A802, Service Manual, Page: 104 / 168

Share
Download
Pioneer CB-A802 Service Manual Download Page 104

DVD-V8000

104

1

2

3

4

1

2

3

4

C

D

F

A

B

E

7.2  UPGRADING 

7.2.1  UPGRADING OF THE FIRMWARE

Upgrading of the firmware is performed, using the CD-R for upgrading.

1

Install the CD-R for upgrading in the tray and press the STOP/OPEN/CLOSE key on the main unit or the OPEN/CLOSE
key on the remote control unit.

2

After the disc is loaded and data on the disc are read, "DOWNLOAD" is displayed on the LCD. Then press the
PLAY/PAUSE on the main unit or the PLAY key on the remote control unit. The disc is ejected, and downloading will start.

3

The indications on the LCD change from ERASE, WRITE, to DL OK. Then the unit will be automatically reset and will
restart. Display the SETUP menu and check that the version of the firmware is upgraded.

If upgrading fails, for example, because a power failure occurred during downloading, downloading via the serial port, by 
connecting a PC is required.

Summary of Contents for CB-A802









































































































































































Reviews:

No comments