pigtronix INFINITY 3 User Manual Download Page 6

Page: 6 / 33

The Loop 1 and Loop 2 footswitch LEDs share the same color coding.
Green = Playback

Red = Recording

Orange = Overdub
Both Loop 1 and Loop 2 footswitch LEDs are accompanied by a red square Arm LED that indicates

which loop is currently armed.
When an external MIDI Clock is used, the Arm LED for the currently selected Loop will blink at the

received tempo.
There is also an optional colorblind mode that utilizes flickering light patterns to supplement the colors.
Solid = Playback

Slow Flicker = Recording

Fast Flicker = Overdub

LEDs

Loop 1, Loop 2, and ARM LEDs

The Stop LED will glow red when loop audio is stopped.
When a delayed command has been initiated, the relevant footswitch, Arm, and Stop LEDs will

blink repeatedly to indicate a pending action, and will turn solid in color once the action is taken.

At the end of the loop cycle of the currently armed loop, the stop, multi-segment digit, associated

footswitch LED, and arm LEDs will all flash. The other (non-armed) loop’s associated LEDs will flash

at the end of its loop cycle as well.

This red LED between the Loop Volume knobs will indicate when the input signal is reaching the

maximum headroom of the Infinity 3’s recording engine and begins to trigger the analog limiter

stages. If the Clip LED is lighting up solid red, reduce the output level of your instrument until the

Clip LED is just beginning to light up at the peaks in your audio signal.

Stop LED

Clip LED

Summary of Contents for INFINITY 3


































Search results

Summary of Contents for INFINITY 3

Reviews:

Related manuals for INFINITY 3

Brands by name

Popular brands

pigtronix INFINITY 3, User Manual

Search results

Summary of Contents for INFINITY 3

Reviews:

Related manuals for INFINITY 3

Brands by name

Popular brands