PIAGGIO NRG POWER PUREJET Workshop Manual Download Page 204

Page: 204 / 248

Static test

Static control after the test ride:

- Starting when warm

- Starter operation

- Minimum hold (turning the handlebar)

- Uniform turning of the steering

- Possible leaks

CAUTION

CHECK AND ADJUST TYRE PRESSURE WITH TYRES AT AMBIENT TEMPERATURE.

CAUTION

NEVER EXCEED THE RECOMMENDED INFLATION PRESSURES OR TYRES MAY BURST.

Functional inspection

Functional check:

Braking system (hydraulic)

- Lever travel

Braking system (mechanical)

- Lever travel

Clutch

- Proper functioning check

Engine

- Throttle travel check

Others

- Check documentation

- Check the frame and engine numbers

- Tool kit

- License plate fitting

- Check locks

- Check tyre pressures

- Installation of mirrors and any accessories

Pre-delivery

NRG Power Purejet

PRE DE - 4

Summary of Contents for NRG POWER PUREJET

























































































































































































































































Search results

Summary of Contents for NRG POWER PUREJET

Reviews:

PIAGGIO NRG POWER PUREJET, Workshop Manual, Page: 204 / 248

Search results

Summary of Contents for NRG POWER PUREJET

Reviews: