manualshive.com logo in svg

PIAGGIO NRG POWER PUREJET, Workshop Manual, Page: 196 / 248

Share
Download
PIAGGIO NRG POWER PUREJET Workshop Manual Download Page 196

Frame central cover

•

Remove the top and bottom fairings.

•

Remove the 2 Philips screws fixing the

footrest.

•

Remove the 3 Allen screws located

around the fuel filler cap.

•

Remove the fuel filler cap.

See also

Side fairings

Knee-guard

•

Remove the footrest and its side fair-

ings.

•

Remove the expansion tank and the

fuel filler cap.

•

Remove the 11 fixing screws, and

hence release the knee-guard.

See also

Footrest

Taillight assy.

•

Remove the top joining element of the

fairings located behind the taillight.

•

Remove the two top fairings.

•

Remove the 2 fixing screws; hence re-

move the taillight after disconnecting

the connector to the vehicle system.

See also

Side fairings

Chassis

NRG Power Purejet

CHAS - 2

Summary of Contents for NRG POWER PUREJET

























































































































































































































































Reviews:

No comments