PIAGGIO Beverly 400 E5 Service Manual Download Page 130

Page: 130 / 159

- Remove the retainer rings and remove the piston.

N.B.

BE CAREFUL NOT TO DAMAGE THE SEALING RINGS
DURING REMOVAL.

Inspecting the small end

N.B.

TO MEASURE WEAR LIMITS AND COUPLING CLEARANCES, SEE THE SPECIFICATIONS CHAP-
TER.

Inspecting the piston

N.B.

TO MEASURE WEAR LIMITS AND COUPLING CLEARANCES, SEE THE SPECIFICATIONS CHAP-
TER.

Inspecting the piston rings

N.B.

TO MEASURE WEAR LIMITS AND COUPLING CLEARANCES, SEE THE SPECIFICATIONS CHAP-
TER.

Removing the piston

- Insert the pin.

- Insert the retainer rings.

CAUTION

POSITION THE ARROW PRINTED ON THE PISTON
CROWN TOWARDS THE EXHAUST OPENING.

CAUTION

AT EVERY NEW MOUNTING USE RETAINER RING PINS.

Engine

Beverly 400 E5

ENG - 130

Summary of Contents for Beverly 400 E5
































































































































































Search results

Summary of Contents for Beverly 400 E5

Reviews:

Related manuals for Beverly 400 E5

Brands by name

Popular brands

PIAGGIO Beverly 400 E5, Service Manual

Search results

Summary of Contents for Beverly 400 E5

Reviews:

Related manuals for Beverly 400 E5

Brands by name

Popular brands