PIAGGIO Beverly 400 E5 Service Manual Download Page 146

Page: 146 / 159

- Remove the oil pump and collect the gasket.

Inspection

- Remove the two screws and remove the oil pump

cover.

- Remove and wash the rotors thoroughly with pet-

rol and compressed air.

- Reassemble the rotors in the pump body, keep-

ing the two reference marks visible.

- Using a feeler gauge, check the distance be-

tween the rotors in the position shown in the figure.

- Check the distance between the outer rotor and

pump body, see figure.

Check the axial clearance of the rotors using a

trued bar as shown in the figure.

Characteristic

Axial rotor clearance

Limit value admitted: 0.09 mm

Distance between the outer rotor and the pump
body

Admissible limit clearance: 0.20 mm

Distance between the rotors

Admissible limit clearance: 0.12 mm

Engine

Beverly 400 E5

ENG - 146

Summary of Contents for Beverly 400 E5
































































































































































Search results

Summary of Contents for Beverly 400 E5

Reviews:

Related manuals for Beverly 400 E5

Brands by name

Popular brands

PIAGGIO Beverly 400 E5, Service Manual

Search results

Summary of Contents for Beverly 400 E5

Reviews:

Related manuals for Beverly 400 E5

Brands by name

Popular brands