PIAGGIO Beverly 400 E5 Service Manual Download Page 125

Page: 125 / 159

- Remove the camshaft.

- Remove the lock of the rockers to allow them to

slide on the pins to access the calibrated pads.

- Remove the calibrated pads

CAUTION

PROPERLY REPLACE THE PADS AND ROCKERS SO AS
TO PRESERVE THE COUPLINGS.

CAUTION

IF NECESSARY USE A TELESCOPIC MAGNET TO RE-
MOVE THE PADS, PAY PARTICULAR ATTENTION THAT
THEY DO NOT FALL IN THE TRANSMISSION HOUSING.

- Remove the pins and the rockers.

N.B.

IF NEEDED, THE HEAD MAY BE REMOVED WITH THE
CAMSHAFT, ROCKER PINS AND FIXING BRACKET. THE
HEAD CAN ALSO BE REMOVED WITHOUT REMOVING
THE CHAIN AND THE CRANKSHAFT CHAIN TENSIONER.

Beverly 400 E5

Engine

ENG - 125

Summary of Contents for Beverly 400 E5
































































































































































Search results

Summary of Contents for Beverly 400 E5

Reviews:

Related manuals for Beverly 400 E5

Brands by name

Popular brands

PIAGGIO Beverly 400 E5, Service Manual

Search results

Summary of Contents for Beverly 400 E5

Reviews:

Related manuals for Beverly 400 E5

Brands by name

Popular brands