PIAGGIO Beverly 400 E5 Service Manual Download Page 110

Page: 110 / 159

- Insert the transmission cover central screw and

tighten it to the prescribed torque.

Locking torques (N*m)

Transmission cover screws

11 ÷ 13

- Insert and tighten the external fixing screws of the

transmission cover to the crankcase to the pre-

scribed torque.

Locking torques (N*m)

Transmission cover screws

11 ÷ 13

- Insert the nut.

- Insert the special tool.

- Rotate the pulley axle until the pulley stops.

Specific tooling

020917Y

Driven pulley stop

- Supporting the tool tighten the fixing screw to the

prescribed screw.

Locking torques (N*m)

Driven pulley M10x1.25 screw

74 ÷ 80

Engine

Beverly 400 E5

ENG - 110

Summary of Contents for Beverly 400 E5
































































































































































Search results

Summary of Contents for Beverly 400 E5

Reviews:

Related manuals for Beverly 400 E5

Brands by name

Popular brands

PIAGGIO Beverly 400 E5, Service Manual

Search results

Summary of Contents for Beverly 400 E5

Reviews:

Related manuals for Beverly 400 E5

Brands by name

Popular brands