PI P-843 User Manual Download Page 6

Page: 6 / 34

2.3.1

Typographic Conventions

Symbol / label

Meaning

1.
2.

Action consisting of one or several steps with strict sequential order

►

Action consisting of one or more steps without relevant sequential or-
der

■

Lists

p. 5

Cross-reference to page 5

RS-232

Label on the product indicating an operating element (example: RS-232
interface socket)

Start > Settings

Menu path in the PC software (example: to open the menu,

Start and

Settings must be clicked successively)

POS?

Command line or a command from PI's General Command Set (GCS)
(example: command to get the axis position)

Device S/N

Parameter name (example: parameter where the serial number is stor-
ed)

Value that must be entered or selected via the PC software

2.3.2

Symbols Used

Symbol / Label

Meaning

General hazard symbol

DANGER

Dangerous situation

Failure to comply could lead to death or serious injury.

►

Precautionary measures for avoiding the risk.

WARNING

Dangerous situation

Failure to comply could lead to serious injury.

►

Precautionary measures for avoiding the risk.

CAUTION

Dangerous situation

Failure to comply could lead to minor injury.

►

Precautionary measures for avoiding the risk.

NOTICE

Dangerous situation

Failure to comply could lead to material damage.

►

Precautionary measures for avoiding the risk.

2 ABOUT THIS DOCUMENT

P843M0001EN

‒

2/23/2021

M O T I O N | P O S I T I O N I N G

Summary of Contents for P-843



































Search results

Summary of Contents for P-843

Reviews:

Related manuals for P-843

Brands by name

Popular brands

PI P-843, User Manual

Search results

Summary of Contents for P-843

Reviews:

Related manuals for P-843

Brands by name

Popular brands