background image

11

sonic station 16

43. C-r/PHNS Only Button

The "Control Room/Phones only" button that is located below 

AUx Return Control 4 allows users to send the AUx Return 4 

post-fader signal to the  Control Room/Phones mixing bus for 

monitoring purposes.

44. returns Solo Button and Indicator

Pushing this buttons allows you to send the signal from all AUx 

Retuns to solo mixing bus(which is, inturn, send to the Control 

Room/Phones  mixing  bus).When  the  solo  is  activated,  the 

corresponding leD indicator will illiminate.

45. AUX Send 1 to 4 Master Controls and Solo Indicator

These controls adjust the final level of the AUX 1,2,3 and 4 

signals(as  taken  from  the AUx  level  controls  1  to  4  on  each 

channel strip), the audio of which is sent to the corresponding 

AUx  sends,  The  corresponding  solo  buttons  allow  you  to 

direct  the  AUx  send  signals  to  the  Control  Room/Phones 

mixing bus for monitoring purposes. When any of the AUx solo 

buttons is activated, the leD will illuminate.

46. Pre/Post Button and Solo Indicator

This button alternates the solo source signals between those of 

post-fader and pre-fader feeds, th be sent to  the solo and Control 

Room/Phones  mixing  bus.  When  the  solo  indicator,located 

beside  the  pre/Post  button,  is  illuminated,  it  means  one  or 

more Solo buttons has been pushed; therefore the Main Level 

meter will display proporties of the solo signal, which is helpful 

in the setting of channel proporties.if solo indicator illuminates 

green, this means the Solo feed is a pre-fader signal; if the solo 

indicator illuminates red, the feed is post fader.

47. Solo Control

When one or more solo buttons are activated on any channel, 

or  on  the  master  section,  this  control  adjusts  the  signals' 

levels  before  sending  the  amplified  signal  to  the  Control 

Room/Phones  mixing  bus. This  enables  the    user  to  be  able 

to switch between monitoring the Main l-R(or other selected 

signals)  and  the  solo  signals  without  being  over-whelmed  by 

the difference in signal levels.

48. 2T return Controls

Turning the 2T Return level control adjusts the signal level of 

the  feed  from  the  2T  Return  inputs.  The  "2T  Return  to  Main 

l-R" button that accompanies this control allows users to send 

the 2T return signal to the Main l-R mixing buses. When the 

"to Main" button is pressed, the Main l-R mix signal is not sent 

to the Rec out, as to avoid producing a feedback loop when 

recorded signals are fed back into the 2T return.

Priority

Signal

High

From solo

low

selected source(s)

Main  l-R  /  group  1-2  /  group  3-4  /  2T 

Return / Aux Return 4

49. Control room / Phones Control

This  control  is  used  to  adjust  the  audio  level  of  the  Control 

Room  and  Phones  feeds,  for  use  in  the  monitoring  and 

tracking of audio. The signal is then sent to the Control Room 

outputs on the rear of the sonic station 16 mixer, as well as the 

Phones jack on the face of the mixer.

The  four  buttons,  located  below  the  Phones  /  Control  Room 

control, allow users to select the various possible sources for 

the  Control  Room  and  Phones  outputs.  By  simply  pushing 

one of these, users have the ability to monitor the 2T return, 

group 1-2, group 3-4, and Main l-R signals, either together or 

individually. There is also a “C-R/Phns onlY” button located 

beneath the Aux Return 4 control, that, when pushed, sends 

the AUx Return 4 signal to the Phones / Control Room mixing 

bus.

50. +48v Indicator

This indicator will illuminate when Phantom Power is activat-

ed.

51. Power Indicator

The Power indicator will light up when the power of the mixer 

is on; in case you weren’t too sure.

52. level Meter

This  dual  12  segment  level  meter  gives  an  accurate  indica-

tion of when audio reach certain levels. The 0 dB indicator il-

luminates is approximately equal to an output level of +4 dBu 

(balanced),  and  the  PeAk  indicator  illuminates  about  1.5  dB 

before  the  signal  is  dynamically  clipped.   To  make  the  maxi-

mum use of audio, set the various level controls so that it sits 

steadily around 0 dB to make full use of audio, while still main-

taining fantastic clarity. 

if  any  solo  buttons  are  activated  on  channels  1  through  16, 

or in the master section, the level Meter will display the solo 

signal’s properties. however, if no solo buttons are activated, 

the Control Room / Phones selected sources (Main l-R, group 

1-2, group 3-4, 2T Return or Aux Return 4) signal properties 

are displayed by the level Meter. in this case, the level meter 

will display the sum of the selected signals.

Summary of Contents for Sonic Station 16









































Reviews: