Phoenix Contact 2702171 User Manual Download Page 29

Page: 29 / 78

Assembly, removal, and electrical installation

106888_en_01

PHOENIX CONTACT

Assembly, removal, and electrical installation

4.1

Assembly and removal

4.1.1

Unpacking the module

•

Read the package slip and follow the instructions.

The module may only be installed and removed by qualified personnel.

4.1.2

Preparation and assembly

•

Mount the module on a 35 mm DIN rail in a control cabinet or junction box protected

from dust and humidity (IP54 or higher).

•

Secure the control cabinet/junction box to prevent unauthorized opening.

•

Only connect the cables using the supplied Axioline F connectors.

NOTE: Electrostatic discharge

The module contains components that can be damaged or destroyed by electrostatic

discharge.

•

When handling the module, observe the safety precautions against electrostatic

discharge (ESD) according to EN 61340-5-1 and IEC 61340-5-1.

WARNING: Unintentional machine startup

Make sure that the power to the system is disconnected before carrying out assembly and

removal work as this could cause unintentional machine startup.

•

Before assembling or removing the module, disconnect the power to the module and

the entire Axioline F station and make sure that the system cannot be switched on

again.

•

Make sure the entire system is reassembled before switching the power back on and

that neither the station nor the system poses a hazard.

Observe the diagnostics indicators and any diagnostic messages.

Downloaded from

Downloaded from

Downloaded from

Downloaded from

Downloaded from

Downloaded from

Downloaded from

Downloaded from

Downloaded from

Downloaded from

Downloaded from

Downloaded from

Downloaded from

Downloaded from

Downloaded from

Downloaded from

Downloaded from

Downloaded from

Downloaded from

Downloaded from

Downloaded from

Downloaded from

Downloaded from

Downloaded from

Downloaded from

Downloaded from

Downloaded from

Downloaded from

Downloaded from

Summary of Contents for 2702171















































































Search results

Summary of Contents for 2702171

Reviews:

Phoenix Contact 2702171, User Manual, Page: 29 / 78

Search results

Summary of Contents for 2702171

Reviews: