Philips LPC2101 User Manual Download Page 28 | Manualshive

Page: 28 / 279

background image

© Koninklijke Philips Electronics N.V. 2006. All rights reserved.

User manual

Rev. 01 — 12 January 2006

28

Philips Semiconductors

UM10161

Volume 1

Chapter 3: System control block

3.8.5 PLL

interrupt

The PLOCK bit in the PLLSTAT register is connected to the interrupt controller. This allows
for software to turn on the PLL and continue with other functions without having to wait for
the PLL to achieve lock. When the interrupt occurs (PLOCK = 1), the PLL may be
connected, and the interrupt disabled. For details on how to enable and disable the PLL
interrupt, see

Section 5.4.4 “Interrupt Enable register (VICIntEnable - 0xFFFF F010)” on

Section 5.4.5 “Interrupt Enable Clear register (VICIntEnClear -

0xFFFF F014)” on page 49

3.8.6 PLL

modes

The combinations of PLLE and PLLC are shown in

Table 18:

PLL Status register (PLLSTAT - address 0xE01F C088) bit description

Bit

Symbol

Description

Reset
value

4:0

MSEL

Read-back for the PLL Multiplier value. This is the value currently
used by the PLL.

0

6:5

PSEL

Read-back for the PLL Divider value. This is the value currently
used by the PLL.

0

7

-

Reserved, user software should not write ones to reserved bits.
The value read from a reserved bit is not defined.

NA

8

PLLE

Read-back for the PLL Enable bit. When one, the PLL is currently
activated. When zero, the PLL is turned off. This bit is automatically
cleared when Power-down mode is activated.

0

9

PLLC

Read-back for the PLL Connect bit. When PLLC and PLLE are both
one, the PLL is connected as the clock source for the
microcontroller. When either PLLC or PLLE is zero, the PLL is
bypassed and the oscillator clock is used directly by the
microcontroller. This bit is automatically cleared when Power-down
mode is activated.

0

10

PLOCK

Reflects the PLL Lock status. When zero, the PLL is not locked.
When one, the PLL is locked onto the requested frequency.

0

15:11

-

Reserved, user software should not write ones to reserved bits.
The value read from a reserved bit is not defined.

NA

Table 19:

PLL Control bit combinations

PLLC

PLLE

PLL Function

0

0

PLL is turned off and disconnected. The CCLK equals the unmodified clock
input.

0

1

The PLL is active, but not yet connected. The PLL can be connected after
PLOCK is asserted.

1

0

Same as 00 combination. This prevents the possibility of the PLL being
connected without also being enabled.

1

1

The PLL is active and has been connected. CCLK/system clock is sourced
from the PLL.

«
...
26
27
28
29
30
...
»

Summary of Contents for LPC2101
























































































































































































































































































Reviews:

No comments

Related manuals for LPC2101

Brand: Camozzi Pages: 33

Brand: Camozzi Pages: 64

Brand: Namron Pages: 3

NOVASTAT EL DIGITAL

Brand: Taconova Pages: 7

Brand: TSM Pages: 2

Brand: EBS Pages: 116

Brand: Daikin Pages: 2

GreenMax DRC DRC07-ED0

Brand: Leviton Pages: 2

Verifi FingerTouch Security

Brand: Zvetco Biometrics Pages: 8

Brand: YASKAWA Pages: 348

Brand: H3C Pages: 15

Brand: Trane Pages: 60

Universal CapSense CY3280-22x45

Brand: Cypress Pages: 55

Brand: Icom Pages: 23

Triton UltraLift

Brand: HydroHoist Pages: 9

Brand: YOKOGAWA Pages: 12

Brand: Sierra Wireless Pages: 58

Brand: Pego Pages: 32

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands