manualshive.com logo in svg

Philips LPC2101, User Manual

The Philips LPC2101 is an innovative and user-friendly device that ensures seamless connectivity. With its advanced features and capabilities, it simplifies your daily tasks. You can easily access the comprehensive User Manual for free download at manualshive.com to make the most of this exceptional product.

Share
Download
background image

 

© Koninklijke Philips Electronics N.V. 2006. All rights reserved.

User manual

Rev. 01 — 12 January 2006 

202

Philips Semiconductors

UM10161

Volume 1

Chapter 16: Timer2 and Timer3

  

Table 175: TIMER/COUNTER2 and TIMER/CT3OUNTER3 register map

Generic 
Name

Description

Access

Reset 
value

[1]

TIMER/
COUNTER2 
Address & 
Name

TIMER/
COUNTER3 
Address & 
Name

IR

Interrupt Register. The IR can be written to clear 
interrupts. The IR can be read to identify which of 
eight possible interrupt sources are pending.

R/W

0

0xE007 0000
T2IR

0xE007 4000
T3IR

TCR

Timer Control Register. The TCR is used to control 
the Timer Counter functions. The Timer Counter can 
be disabled or reset through the TCR. 

R/W

0

0xE007 0004
T2TCR

0xE007 4004
T3TCR

TC

Timer Counter. The 16-bit TC is incremented every 
PR+1 cycles of PCLK. The TC is controlled through 
the TCR.

R/W

0

0xE007 0008
T2TC

0xE007 4008
T3TC

PR

Prescale Register. The Prescale Counter (below) is 
equal to this value. The next clock increments the 
TC and clears the PC.

R/W

0

0xE007 000C
T2PR

0xE007 400C
T3PR

PC

Prescale Counter. The 16-bit PC is a counter which 
is incremented to the value stored in PR. When the 
value in PR is reached, the TC is incremented and 
the PC is cleared. The PC is observable and 
controllable through the bus interface.

R/W

0

0xE007 0010
T2PC

0xE007 4010
T3PC

MCR

Match Control Register. The MCR is used to control 
if an interrupt is generated and if the TC is reset 
when a Match occurs.

R/W

0

0xE007 0014
T2MCR

0xE007 4014
T3MCR

MR0

Match Register 0. MR0 can be enabled through the 
MCR to reset the TC, stop both the TC and PC, 
and/or generate an interrupt every time MR0 
matches the TC. 

R/W

0

0xE007 0018
T2MR0

0xE007 4018
T3MR0

MR1

Match Register 1. See MR0 description.

R/W

0

0xE007 001C
T2MR1

0xE007 401C
T3MR1

MR2

Match Register 2. See MR0 description.

R/W

0

0xE007 0020
T2MR2

0xE007 4020
T3MR2

MR3

Match Register 3. See MR0 description.

R/W

0

0xE007 0024
T2MR3

0xE007 4024
T3MR3

CCR

Capture Control Register. The CCR controls which 
edges of the capture inputs are used to load the 
Capture Registers and whether or not an interrupt is 
generated when a capture takes place.

R/W

0

0xE007 0028
T2CCR

0xE007 4028
T3CCR

CR0

Capture Register 0. CR0 is loaded with the value of 
TC when there is an event on the CAP2.0 input.

Note:

 CAP3.0 not usable on Timer 3

RO

0

0xE007 002C
T2CR0

0xE007 402C
T3CR0

CR1

Capture Register 1. See CR0 description.

Note:

 CAP3.1 not usable on Timer 3 

RO

0

0xE007 0030
T2CR1

0xE007 4030
T3CR1

CR2

Capture Register 2. See CR0 description.

Note:

 CAP3.2 not usable on Timer 3

RO

0

0xE007 0034
T2CR2

0xE007 4034
T3CR2

Summary of Contents for LPC2101
























































































































































































































































































Reviews:

No comments

Related manuals for LPC2101

Balmar Max Charge MC-624 Installation And Operator'S Manual preview
Max Charge MC-624
Brand: Balmar Pages: 8
Balmar MAX CHARGE MC-614 Installation And Operation Manual preview
MAX CHARGE MC-614
Brand: Balmar Pages: 20
Fagor CNC 8070 Programming Manual preview
CNC 8070
Brand: Fagor Pages: 556
J+J J4C Series Installation Instructions preview
J4C Series
Brand: J+J Pages: 2
Interlogix TruPortal TP-ADD-1DIP Quick Reference preview
TruPortal TP-ADD-1DIP
Brand: Interlogix Pages: 9
ZPA Pecky, a.s. 52 442 Mounting Instructions preview
52 442
Brand: ZPA Pecky, a.s. Pages: 36
Computer Automation Technology CAT-250 Manual preview
CAT-250
Brand: Computer Automation Technology Pages: 55
Eaton Cutler-Hammer LMR Instructions Manual preview
Cutler-Hammer LMR
Brand: Eaton Pages: 38
Bailey infi 90 IMMFP12 Instruction preview
infi 90 IMMFP12
Brand: Bailey Pages: 75
Epsolar eTracer ET4415BND Operation Manual preview
eTracer ET4415BND
Brand: Epsolar Pages: 44
IFM EC2121 System Manual preview
EC2121
Brand: IFM Pages: 41
Kelly KLS4812S User Manual preview
KLS4812S
Brand: Kelly Pages: 32
Maverick EP7312 User Manual preview
EP7312
Brand: Maverick Pages: 122
SSHC TSSHC-3IL-24 Quick Start Manual preview
TSSHC-3IL-24
Brand: SSHC Pages: 2
Altera Stratix III Using Manual preview
Stratix III
Brand: Altera Pages: 59
Samson TROVIS 6495 Series Mounting And Operating Instructions preview
TROVIS 6495 Series
Brand: Samson Pages: 156
Zapi ADPZP0CC User Manual preview
ADPZP0CC
Brand: Zapi Pages: 36
Harmonic Drive YukonDrive-1021 Operating Manual preview
YukonDrive-1021
Brand: Harmonic Drive Pages: 53

Brands by name

Popular brands

Load more brands