manualshive.com logo in svg

Philips LPC2101, User Manual

The Philips LPC2101 is an innovative and user-friendly device that ensures seamless connectivity. With its advanced features and capabilities, it simplifies your daily tasks. You can easily access the comprehensive User Manual for free download at manualshive.com to make the most of this exceptional product.

Share
Download
background image

 

© Koninklijke Philips Electronics N.V. 2006. All rights reserved.

User manual

Rev. 01 — 12 January 2006 

167

Philips Semiconductors

UM10161

Volume 1

Chapter 13: SSP

  

13.3 Bus description

13.3.1 Texas 

Instruments 

Synchronous Serial (SSI) frame format

Figure 41

 show the 4-wire Texas Instruments synchronous serial frame format supported 

by the SSP module.

SSEL1

I/O

SSEL

FS

CS

Slave Select/Frame Sync/Chip Select.

 When the SSP is a 

bus master, it drives this signal from shortly before the start 
of serial data, to shortly after the end of serial data, to signify 
a data transfer as appropriate for the selected bus and 
mode. When the SSP is a bus slave, this signal qualifies the 
presence of data from the Master, according to the protocol 
in use. When there is just one bus master and one bus 
slave, the Frame Sync or Slave Select signal from the 
Master can be connected directly to the slave’s 
corresponding input. When there is more than one slave on 
the bus, further qualification of their Frame Select/Slave 
Select inputs will typically be necessary to prevent more 
than one slave from responding to a transfer.

MISO1

I/O

MISO

DR(M)
DX(S)

SI(M)
SO(S)

Master In Slave Out.

 The MISO signal transfers serial data 

from the slave to the master. When the SSP is a slave, serial 
data is output on this signal. When the SSP is a master, it 
clocks in serial data from this signal. When the SSP is a 
slave and is not selected by SSEL, it does not drive this 
signal (leaves it in HIGH impedance state).

MOSI1

I/O

MOSI

DX(M)
DR(S)

SO(M)
SI(S)

Master Out Slave In.

 The MOSI signal transfers serial data 

from the master to the slave. When the SSP is a master, it 
outputs serial data on this signal. When the SSP is a slave, it 
clocks in serial data from this signal.

Table 146: SSP pin descriptions

Pin Name

Type

Interface pin name/function

Pin Description

SPI

SSI

Microwire

Summary of Contents for LPC2101
























































































































































































































































































Reviews:

No comments

Related manuals for LPC2101

ABB ControlMaster CM15 Instructions preview
ControlMaster CM15
Brand: ABB Pages: 4
ZKTeco PA10 Quick Start Manual preview
PA10
Brand: ZKTeco Pages: 8
EasyIO FT Series User Reference preview
FT Series
Brand: EasyIO Pages: 18
Kärcher K 3 How To Connect preview
K 3
Brand: Kärcher Pages: 4
Lattice Semiconductor MachXO5-NX Development Kit Quick Start preview
MachXO5-NX Development Kit
Brand: Lattice Semiconductor Pages: 2
IDTECK Star RFL200 Quick Manual preview
Star RFL200
Brand: IDTECK Pages: 12
Banner XS26-2 Series Manual preview
XS26-2 Series
Brand: Banner Pages: 2
Eaton CGLine+ Web Controller Installation And Operating Instructions Manual preview
CGLine+ Web Controller
Brand: Eaton Pages: 28
phytron MCC-2 Manual preview
MCC-2
Brand: phytron Pages: 55
H.E. Anderson Ratio Feeder J+ Advanced Series Manual preview
Ratio Feeder J+ Advanced Series
Brand: H.E. Anderson Pages: 11
Window Master MotorController WCC 310 Installation Instructions Manual preview
MotorController WCC 310
Brand: Window Master Pages: 19
JBSYSTEMS Light LS-RGB-DMX CONTROL Manual preview
LS-RGB-DMX CONTROL
Brand: JBSYSTEMS Light Pages: 12
KEPCO MST 488-27HT Operator'S Manual preview
MST 488-27HT
Brand: KEPCO Pages: 34
National Instruments AMUX-64T Installation Manual preview
AMUX-64T
Brand: National Instruments Pages: 3
Kelly KLS14801-8080N User Manual preview
KLS14801-8080N
Brand: Kelly Pages: 43
ZPA Pecky, a.s. MODACT MTNED 15 Mounting Instructions preview
MODACT MTNED 15
Brand: ZPA Pecky, a.s. Pages: 48
Galcon DC-11SF Installation And Operating Instructions Manual preview
DC-11SF
Brand: Galcon Pages: 24
NXP Semiconductors freescale Kinetics TWR-K60N512-KEIL Quick Start Manual preview
freescale Kinetics TWR-K60N512-KEIL
Brand: NXP Semiconductors Pages: 5

Brands by name

Popular brands

Load more brands