Phihong POE125U-4AT-N-R User Manual Download

Page: 31 / 44

Phihong USA Corporation | 47800 Fremont Blvd., Fremont, CA 94538 | 1.510.445.0100 | www.phihong.com

Open the MIB Browser and click the

Continue

button on the

Welcome

popup window. A

Tip of the Day

window may pop-up for certain options in this browser. Users may choose

to click the little box in the lower left hand corner to stop these pop-ups.

Click the

MIB

tab; remove any MIB modules in the “Loaded MIB modules” by

highlighting and double clicking them.

Under the

Action

menu - open

Run MIB

Compiler

In the MG-SOFT MIB Compiler window, click

File

then

Compile……

then in the

Open

window, browse for and open PHIHONG-POE-MIB.txt (users can get

SNMP MIB rev

10/30/09

from the support section on either

www.phihong.com

If compiling is successful, a Compiled MIB Modules window will be displayed. Click

Save

All

and click

on the

Browse for Folder

window.

Close the

MG-SOFT MIB Compiler

window.

In the

MG-SOFT MIB Browser

window, click the circular arrow button (the middle one

of 5 buttons right below

the Loaded MIB modules

window). This will update the MIB

Browser windows’ contents (including the newly compiled MIB module Phihong-POE-
MIB).

In the lower window, click the tab

MIB Modules

. Locate the Module < Phihong-POE-

MIB >. Highlighting and double clicking it will load it into the upper

Loaded MIB

modules

window.

Also locate <RFC1213-MIB> and <SNMPv2-MIB>, load them into the upper

Loaded

MIB modules

window.

10.

Now the setup for Phihong’s Midspan SNMP interface is complete.

Summary of Contents for POE125U-4AT-N-R













































Search results

Summary of Contents for POE125U-4AT-N-R

Reviews:

Related manuals for POE125U-4AT-N-R

Brands by name

Popular brands

Phihong POE125U-4AT-N-R, User Manual

Search results

Summary of Contents for POE125U-4AT-N-R

Reviews:

Related manuals for POE125U-4AT-N-R

Brands by name

Popular brands