Phase 3 J-3 CUB 370 RTF Operating Instructions Manual Download Page 16

6

STeP 4:  RANGe TeSTING THe RADIO CONTROL SYSTeM

After getting out to your flying field, but before you fly for the first time, you must range test the radio control system.  This will ensure 
that the transmitter is "talking" correctly to the airplane.  You should follow this procedure before every first flight of the day and after 

you have a hard landing, crash, or after a repair.

  Turn on the transmitter, then plug in the flight battery and install it into the fuselage.

  Set the airplane on the ground and extend the transmitter's antenna completely.  Move the right-hand control stick on the transmit

-

ter several times to check the controls.  They should operate smoothly.

  Walk approximately 75ft. (25m) from the airplane and move the right-hand control stick on the transmitter once more.  Check to 

make sure that the controls are operating smoothly at this distance.  You may need a friend to help you with this step.

WARNING

  

If the airplane does not range check, don't fly!  Please refer to the troubleshooting guide on page # 22.

  The flying field you choose should be a large, open field with grass.  There should not be any vehicles, buildings, power lines, 

trees, large rocks or anything else that your airplane can crash into.

STeP 3:  CHOOSING YOuR FLYING FIeLD

YOuR FIRST FLIGHT

After all this, we bet you're ready to actually go flying!  If you've skipped anything prior to this section, we suggest going back through 

the instructions.  Doing so will help ensure your success.

Some Things to Remember:

  With the flight battery fully charged, you can expect anywhere from 4-6 minutes of flight time, so plan your landing accordingly.

  Make sure that your flying field has no obstructions you can fly into. 

 

  The flying field should be large enough that you can land anywhere if you get into trouble.  Until you are proficient at flying the 

airplane, you don't want to have to worry about landing in a small, localized area.

  There should be no wind during your first few flights; also try to orientate yourself so you're not looking directly into the sun while 

flying.

  Fully charge the flight battery just before coming to the flying field.  Do not charge the flight battery the night before, then go flying 

the next day.  The flight battery will have lost some charge and it won't produce full power.

  Double-check that the elevator and rudder control surfaces are moving in the correct direction.  If they aren't, flip the servo reversing 

switches as described on page # 3.

  Double-check that the elevator and rudder control surfaces are centered and that the trim tabs on the transmitter are centered, too.  

If not, center them as described on page # 3.

***WARNING***WARNING***WARNING***WARNING***WARNING***WARNING***

If at any time during your flight, the airplane gets stuck up in a tree, in power lines or on a roof top, 

DO NOT attempt to retrieve the 

airplane yourself.

  The airplane is not worth the risk.  We strongly suggest contacting a professional for assistance.  Attempting to 

retrieve the airplane yourself in any of these cases could potentially result in extreme harm or even death.

Continued On Next Page

 

Summary of Contents for J-3 CUB 370 RTF























Reviews: