manualshive.com logo in svg

Pfeiffer Vacuum Prisma QMS 200, Operating Manual

Share
Download
Pfeiffer Vacuum Prisma QMS 200 Operating Manual Download Page 25

BG 805 201 BE     (9911)     QMS200.om

25

DANGER

Disconnect the 24V power supply of the QME from the AC power source before
any moist cleaning.
Make sure the connectors do not get moist. No liquid must seep into the unit. Do
not operate the unit until it is completely dry.

Replace the filter mat if it is decomposed or if it can no longer be cleaned as
described above.

n

Disconnect the 24 V power supply from the AC power source and detach all
electrical connections to the QME.

o

Separate the QME from the analyzer by performing the same steps as
described in Chapter 3.2.4 QME installation but in reverse order.

p

Set the QME on a flat surface with the front panel facing upward.

tune

control

LAN

ready

24V

RS-232-C

VACUUM

q

Unfasten the screws illustrated in the drawing (do not lose the lock washers)
and remove the front panel.

r

Replace the now accessible filter mat with a new one.

s

Reassemble the unit by performing the above steps in reverse order. Do not
forget to reinstall the lockwashers.

5.2.2 Replacing the filter mat

q

q

q

q

Summary of Contents for Prisma QMS 200





































Reviews:

No comments

Brands by name

Popular brands

Load more brands