manualshive.com logo in svg

Pfeiffer Vacuum Prisma QMS 200, Operating Manual

Share
Download
Pfeiffer Vacuum Prisma QMS 200 Operating Manual Download Page 21

BG 805 201 BE     (9911)     QMS200.om

21

4 Operation

DANGER

Caution: damaged product
Putting a damaged product into operation can be extremely hazard-
ous.
In case of visible damages, make sure the product is not put into
operation.

WARNING

Make sure that the limits and ambient conditions specified in the technical data
(

→

 

 8,9) are met.

DANGER

The power plug may only be plugged into an AC outlet that is equipped with a
protective ground contact. Use only a matching three-conductor power cable with
correct ground connection. The protective effect must not be defeated by an
extension cable without protective ground conductor.

WARNING

Check the vacuum in the QMA before you insert the power plug of the SP 200.
Required vacuum conditions:

<10

-4

 mbar with Faraday type

<10

-5

 mbar with Channeltron type

If you use the compact gauge head connected to the QME, the power plug may
be inserted without checking the vacuum conditions. But do not turn on the
Emission and Channeltron voltage until the above limits have been attained.
Activate EXT_PROT (

→

 

 17) monitoring.

n

n

n

n

Insert the power plug.

WARNING

The power plug should be easily accessible. If this is not the case at the
installation site, a power switch or connector must be provided in an easily
accessible location.

4.1 Commissioning

SP 200

Summary of Contents for Prisma QMS 200





































Reviews:

No comments

Brands by name

Popular brands

Load more brands