Permobil Corpus 3G Service Manual Download Page 8

Page: 8 / 45

Adjustment

Adjusting the seat depth

10.

Mount UniTrack rails of a suitable length for the

seat depth setting. See the table on 43. The

rails are each held in place by two screws. See

the illustration. Use a torque wrench to tighten

the screws.

Tightening torque 9.8 Nm.

11.

Mount seat plates of a suitable length for the

seat depth setting. See the table on 43. The

plates are held in place by two screws at the

back edge and two quick-mount clamps at the

front. See the illustration.

12.

Fit a cushion of a suitable length/width for

this setting. See the table on 43. Secure the

cushion in place using the Velcro on the back

of the cushion.

The UniTrack rails are fixed in place

with two screws each.

The seat plates are held in place by two

screws at the back edge and two quick-mount

clamps at the front.

The seat's mounting position on the seat lift/fixed seat column may need to be changed following

adjustment of seat depth. Failure to do this correctly may impair the driving properties of the

wheelchair, leading to an increased risk of personal injury and damage to property, including

damage to the wheelchair. See 37 for further information.

WARNING!

Summary of Contents for Corpus 3G














































Search results

Summary of Contents for Corpus 3G

Reviews:

Related manuals for Corpus 3G

Brands by name

Popular brands

Permobil Corpus 3G, Service Manual

Search results

Summary of Contents for Corpus 3G

Reviews:

Related manuals for Corpus 3G

Brands by name

Popular brands