Permobil Corpus 3G Service Manual Download Page 41

Page: 41 / 45

Replacing the footplate

Removal

Switch off the main power switch on the control

panel.

Remove the screw holding the footplate in

place. See the illustration below.

Remove the footplate friction brake by taking

the parts off the shaft. See the illustration

below.

Remove the footplate by taking it off the shaft.

See the illustration below.

Mounting

Mount the footplate by sliding it onto the shaft.

See the illustration below.

Mount the footplate friction brake by sliding

the parts onto the shaft. Make sure that the

metal butt is positioned in the intended hole in

the footplate. See the illustration to the right.

Fit the screw that holds the footplate in place.

See the illustration below. Tighten the screw

using a torque wrench.

Tightening torque

33 Nm.

For this task the following tools are necessary:

1 Allen key 5 mm

The friction brake's metal butt is in place in the

intended hole in the footplate

The footplate and its friction brake

Repairs

Replacing the footplate

Do not subject the footplate to load during

mounting or removal. Risk of crushing.

WARNING!

Summary of Contents for Corpus 3G














































Search results

Summary of Contents for Corpus 3G

Reviews:

Related manuals for Corpus 3G

Brands by name

Popular brands

Permobil Corpus 3G, Service Manual

Search results

Summary of Contents for Corpus 3G

Reviews:

Related manuals for Corpus 3G

Brands by name

Popular brands