Permobil Corpus 3G Service Manual Download Page 37

Page: 37 / 45

Replacing a legrest

For this task the following tools are necessary:

1 Allen key 5 mm

1 Allen key 8 mm

Remove the legrest's top cover by carefully

pulling it straight out

Remove the front ends of the UniTrack rails

The legrest is held in place by two screws and spacers.

The front bracket of the actuator is held in place by a screw and lock nut.

Removal

Switch off the main power switch on the control

panel.

Remove the legrest's top cover by carefully

pulling it straight out. See the illustration.

Remove the front ends of the UniTrack rails.

See the illustration.

Remove the front bracket of the manual

adjustment unit/actuator. See the illustration

below. Start with the lock nut and the washer

on the inside of the bracket, then remove the

screw and washer.

Remove the legrest, which is held in place by

two screws and spacers. See the illustration

below.

Repairs

Replacing a legrest

Do not subject the legrest to load during mounting

or removal. Risk of crushing.

WARNING!

Summary of Contents for Corpus 3G














































Search results

Summary of Contents for Corpus 3G

Reviews:

Related manuals for Corpus 3G

Brands by name

Popular brands

Permobil Corpus 3G, Service Manual

Search results

Summary of Contents for Corpus 3G

Reviews:

Related manuals for Corpus 3G

Brands by name

Popular brands