Pentax 645 NII Operating Manual Download Page 84

Page: 84 / 100

ADV

NCE

ERATIONS

[PF9] Changing the number of frames taken
Changes the number of recordable frames when a 120 film or 220 film is used.

Pentax Function No.9

The number of recordable frames shown on the LCD panel is varied according to the type of the film holder
attached.

•

With 16 or 33 frames set, focus may deteriorate on the 2nd frame taken in the Consecutive-frame mode.

•

The number of frames taken can be changed before the 1st frame is taken. After the 1st frame is taken,
the number of frames cannot be changed until the film is removed.

LCD panel indication

Setting contents

With 120 film attached

With 220 film attached

15 or 32 frames (initial setting)

With 120 film holder ... 15 frames
With 220 film holder ... 32 frames

16 or 33 frames

With 120 film holder ... 16 frames
With 220 film holder ... 33 frames

Summary of Contents for 645 NII





































































































Search results

Summary of Contents for 645 NII

Reviews:

Related manuals for 645 NII

Brands by name

Popular brands

Pentax 645 NII, Operating Manual

Search results

Summary of Contents for 645 NII

Reviews:

Related manuals for 645 NII

Brands by name

Popular brands