Pentax 645 NII Operating Manual Download Page 75 | Manualshive

Page: 75 / 100

background image

73

ADV

A

NCE

D

OP

ERATIONS

Slow-Speed-Sync Shooting

Purpose

It is possible to balance the exposure of a fore-
ground subject against a dimly lit background by
using the flash to properly expose the foreground
subject and a slow-shutter-speed to expose the low
light background.

To set
With the Metered Manual Mode set
1. Turn the flash on.
2. Set the camera's exposure mode to the

Metered Manual Mode.

3. Select an appropriate shutter speed (lower

than 1/60 second) and aperture combination
for a correct exposure.

4. Release the shutter.

To set
With the Shutter-Priority AE Mode set
1. Set the camera's exposure mode to the Shut-

ter-Priority AE Mode.

2. Set the desired shutter speed.

•

lf the aperture in the viewfinder blinks, a correct
exposure will not be obtained for the background.
Adjust the shutter speed until the blinking stops.

3. Turn the flash on.
4. Take the picture.

•

lf the power is on before the desired shutter
speed is selected, the proper exposure for the
back-ground will not be obtained. Be sure to
select the shutter speed before the flash is turned
on.

•

ln the slow-speed-sync shooting, use of a tripod is
recommended to prevent camera shake.

«
...
73
74
75
76
77
...
»

Summary of Contents for 645 NII





































































































Reviews:

No comments

Related manuals for 645 NII

Brand: Canon Pages: 22

PowerShot S400 Digital Elph

Brand: Canon Pages: 2

PowerShot S230 DIGITAL ELPH

Brand: Canon Pages: 2

PowerShot S110 Digital ELPH

Brand: Canon Pages: 7

Brand: Canon Pages: 9

PowerShot SD10 Digital ELPH

Brand: Canon Pages: 2

PowerShot S400 Digital Elph

Brand: Canon Pages: 138

Brand: Canon Pages: 186

Brand: Canon Pages: 106

PowerShot SD100

Brand: Canon Pages: 21

PowerShot S3 IS Digital Camera

Brand: Canon Pages: 27

Brand: Canon Pages: 15

PowerShot S3 IS Digital Camera

Brand: Canon Pages: 2

Brand: Canon Pages: 15

Brand: Canon Pages: 212

Brand: Canon Pages: 4

Brand: Canon Pages: 2

Brand: Canon Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands