Pentax 645 NII Operating Manual Download Page 77

Page: 77 / 100

ADV

NCE

ERATIONS

Mirror Lock-up

This camera is equipped with a mirror lock-up function.

To set
1. Set the drive mode selector to

2. Press the shutter release button fully to swing up

the mirror.

3. Press the shutter release button again. The shutter

is released.

•

The exposure is locked just before the mirror goes up.

•

The audible PCV signal's beeping can be enabled and
will be heard with the drive mode selector set to

•

Mirror lockup cannot be used when using LS lenses
with the lens shutter set.

•

Mirror lockup cannot be operated when the batteries are
exhausted or running low. The batteries run out quickly
when using mirror lock-up for long hours.

To cancel
1. With the exposure mode set to the Aperture-Prior-

ity AE mode, Metered manual mode or Bulb expo-
sure mode:

Set the Drive mode selector to a position other than
[M.UP] or set the main switch to [OFF].

2. With the exposure mode set to the Programmed AE

or Shutter- Priority AE mode:

Set the multi-exposure switch to [ON].

Set the drive mode selector to a position other than
[M.UP] or set the main switch to [OFF].

Set the multi-exposure switch to the original position.

Note:

Without setting the multi-exposure switch to the ON posi-
tion, the film is advanced by 1 frame when the mirror
returns to the original position.

To set

To cancel 1

To cancel 2

Summary of Contents for 645 NII





































































































Search results

Summary of Contents for 645 NII

Reviews:

Related manuals for 645 NII

Brands by name

Popular brands

Pentax 645 NII, Operating Manual

Search results

Summary of Contents for 645 NII

Reviews:

Related manuals for 645 NII

Brands by name

Popular brands