Pentair HIGH POWER WIRELESS LINK KIT Installation Manual Download Page 2

High Power Wireless Link Kit Installation Guide

 

2

 

                                                                                                                                                                                            

3

 

Technical Support

Phone: (800) 831-7133 - www.pentair.com

  

 

Contents

FCC Regulatory Safety Notice ........................................................................... 3
 

    High Power Wireless Link Kit Overview ............................................................. 4

High Power Wireless Link Kit Contents .............................................................. 4

High Power Wireless Link Indoor Transceiver LEDs and Connectors ................ 5

High Power Wireless Link For ScreenLogic Interface Systems .................. 6
    Mounting Indoor Transceiver .......................................................................... 6
    Mounting Outdoor Transceiver ....................................................................... 8 

       Connect Transceiver Cable to the RS-485 COM Port ..................................... 8

IntelliCenter Control System
(Replacing Existing Wireless Antenna with HPW Link)  .......................13-14

IntelliCenter Control System 

   (Without an Existing Transceiver)  ...........................................................13-16

P/N 523445 Rev. A 1/2019

Summary of Contents for HIGH POWER WIRELESS LINK KIT

















Reviews: