background image

7

 

Check motor.  

 It may be equipped 
with an automatic 

resetting thermal  
protector and may restart unexpectedly  
(see specifications chart). Protector tripping 
is an indication of motor overloading as a 
result of operating the pump at too high a 
pressure (over 125 PSI), too high of viscosity, 
too high of specific gravity, excessively high 
or low voltage, inadequate wiring, incorrect 
motor connections, too small a motor (sized 
incorrectly, not enough HP), or a defective 
motor or pump.
Do not handle pump with wet hands  
or when standing in water. Failure to  
follow the General Safety Information  
and all warnings could result in fatal  
electrical shock!

Assembly  

(If pump and motor are  
pre-assembled, skip assembly.)
If a pump head needs to be coupled to 
an electric motor, then the following 
procedure should be followed. (See 
Figures 3 and 4.) First, install one of 
the two coupling halves and key on 
the pump shaft and tighten the set 
screw. The shaft end should be even or 
slightly recessed from the coupling half 
(approximately 1/8”). The other  
coupling half must be installed on the 
motor shaft. To do this, it should be 
placed on the shaft with the key,  
with the shaft recessed approximately 
1/2”. The set screw is not yet tight-

ened. It is necessary to establish a gap 
between the coupling halves of  
approximately .02” to .05” (See Figure 
4).  A thin piece of cardboard or a piece 
of paper folded up will work fine to set 
this gap. The pump is placed into posi-
tion on the motor and the position of 
the motor coupling half is established 
using the piece of thin cardboard or 
other gauge material. The motor  
coupling half is tightened. The pump  
is removed, the coupling spider (rubber 
piece) is placed into position, and the 
pump bolted to the motor using the 
four bolts. 

SHURflo Operating Instructions, Performance,  

Specifications and Parts Manual

Viton Models GMSV2A, GMSV4A, GMSV6C, GMSV2A3T, GMSV2A33T, 

GMSV4A5T, GMSV4A53T, GMSV6C7T and GMSV6C73T  

Teflon

®

 Models GMST2A, GMST4A, GMST6C, GMST2A3T, GMST2A33T, 

GMST4A5T, GMST4A53T, GMST6C7T and GMST6C73T 

Form L-4089 (2/17) 

Figure 3 - Pump Motor Assembly

Figure 4 - Assembly Coupler

Coupler Gap

Key

Key

Spider

Spider

Pump Shaft

Key

Coupling Halves

Coupling Half

Cutaway of Pump End

Motor Shaft

Motor

Summary of Contents for SHURflo Teflon GMST2A

















Reviews: