PENSOTTI PCC 34-H Instruction Manual Download Page 66

Page: 66 / 72

INSTALLATION INSTRUCTIONS

Regulating the water temperature in accordance with the outdoor temperature

The outdoor sensor has to be connected directly to circuit board.

In case of outdoor temperature sensor installation, the climatic compensation curve is set using the
central heating control knob. As the knob (see fig. 2) is rotated, the numbers corresponding to the curve shown
in figure 1 are displayed

The factors governing the correction are reported in figure 1.

The selection of the compensation curve is determined by the maximum delivery temperature Tm and the
minimum outdoor temperature Te.

N.B.

The y-axis values of the delivery temperature Tm refer to standard 185-95 °F appliances or 104-77 °F floor-

mounted appliances. The type of appliance can be programmed using parameter 3 (see 5.1

“Parameter

programming

”).

OUTDOOR SENSOR

DELIVERY TEMPERATURE CORRECTION AS A FUNCTION OF OUTSIDE

TEMPERATURE WITH RESPECT TO THE POSITION OF THE HEATING

TEMPERATURE CONTROL SET BY THE USER

Summary of Contents for PCC 34-H









































































Search results

Summary of Contents for PCC 34-H

Reviews:

Related manuals for PCC 34-H

Brands by name

Popular brands

PENSOTTI PCC 34-H, Instruction Manual

Search results

Summary of Contents for PCC 34-H

Reviews:

Related manuals for PCC 34-H

Brands by name

Popular brands