Pella Insynctive Lifestyle Series Product Manual Download Page 2

Page: 2 / 16

Pella

Lifestyle Series Motorized, Integrated Blinds and Shades with Insynctive | 2

Table of Contents

3 General and Safety Information

• Need Help?

• Have a Home Automation System?

• Warnings

4 Product Overview

• Specifications

5 Detailed Instructions

• Setting Up Pella® Lifestyle Series Motorized, Integrated Blinds or Shades

• Programming Positions

• Operating Blinds or Shades with Remote

• Tilting Blind Slats

• Pairing to Pella Bridge

• With Home Automation

10 Additional Instructions

• Charging Battery in Blinds or Shades

• Care and Maintenance

• Replacing Batteries

• Adding or Deleting a Remote

• “Homing” Blinds or Shades

• Resetting to Factory Defaults

13 Troubleshooting

14 Inductive Charging Instructions

• Getting Started

• Using the Charger

• LED Color Indicators on Transmitter

16 FCC Compliance and Industry Canada

•

Limited Warranty

Summary of Contents for Insynctive Lifestyle Series

















Search results

Summary of Contents for Insynctive Lifestyle Series

Reviews:

Related manuals for Insynctive Lifestyle Series

Brands by name

Popular brands

Pella Insynctive Lifestyle Series, Product Manual

Search results

Summary of Contents for Insynctive Lifestyle Series

Reviews:

Related manuals for Insynctive Lifestyle Series

Brands by name

Popular brands