3 Day Blinds VERTICAL BLINDS Getting Started Download

Page: 1 / 10

| Vertical Blinds

GETTING STARTED

VERTICAL BLINDS

OPTIONAL HARDWARE

Plastic Corner

Corner End Cap

Corner Pieces

Valance Corner

(Closed)

For Vinyl Blinds

Valence Return

Fabric

Vane Weight

Outside Mount

Valance Clip

Fabric Vane Chain

A few simple tools are required:

Included in your order is all the hardware necessary for a

normal installation. Depending on the mounting surface,

fasteners other than the screws provided may be required.

Wall board and plaster require the use of anchors such as

expansion or toggle bolts. Bricks, tile and stone need special

plugs and drill bits. Wood should always be pre-drilled to

avoid splitting.
Professional installation is also available in most areas,

call 800-800-3329.

Steel Tape Measure

Power Drill and

Drill Bits

Awl (or tool for starting

a screw hole)

Level

(for outside mount)

Pencil

Flathead & Phillips

Screwdriver

STANDARD HARDWARE

Screws

Inside Mount

Headrail Clip

L-Bracket

Tension Bracket

With Screws

Summary of Contents for VERTICAL BLINDS











Search results

Summary of Contents for VERTICAL BLINDS

Reviews:

Related manuals for VERTICAL BLINDS

Brands by name

Popular brands

3 Day Blinds VERTICAL BLINDS, Getting Started

Search results

Summary of Contents for VERTICAL BLINDS

Reviews:

Related manuals for VERTICAL BLINDS

Brands by name

Popular brands