manualshive.com logo in svg

PeakTech 1190, Operation Manual

Share
Download
PeakTech 1190 Operation Manual Download Page 2

1. Safety Precautions

This product complies with the requirements of the following European Community Directives: 2004/108/EC 

(Electromagnetic Compatibility) and 2006/95/EC (Low Voltage) as amended by 2004/22/EC (CE-Marking).   

Overvoltage category II; pollution degree 2. 

To  ensure  safe  operation  of  the  equipment  and  eliminate  the  danger  of  serious  injury  due  to  short-circuits 

(arcing), the following safety precautions must be observed. 

Damages  resulting  from  failure  to  observe  these  safety  precautions  are  exempt  from  any  legal  claims 

whatever. 

Do not use this instrument for high-energy industrial installation measurement.

Prior to connection of the equipment to the mains, check that the available mains voltage corresponds

to the voltage setting of the equipment.

Connect the mains plug of the equipment only to a mains outlet with earth connection.

Do not place the equipment on damp or wet surfaces.

Do not operate the equipment near strong magnetic fields (motors, transformers etc.).

Do not exceed the maximum permissible input ratings (danger of serious injury and/or destruction of

the equipment).

The meter is designed to withstand the stated max voltages. If it is not possible to exclude without that

impulses, transients, disturbance or for other reasons, these voltages are exceeded a suitable presale

(10:1) must be used.

Replace a defective fuse only with a fuse of the original rating. Never short-circuit fuse or fuse holding.

Disconnect test leads or probe from the measuring circuit before switching modes or functions.

Check test leads and probes for faulty insulation or bare wires before connection to the equipment.

Conduct measuring works only in dry clothing and rubber shoes, i. e. on isolating mats.

Never touch the tips of the test leads or probe.

Comply with the warning labels and other info on the equipment.

The measurement instrument is not to be to operated unattended.

Always start with the highest measuring range when measuring unknown values.

Do not subject the equipment to direct sunlight or extreme temperatures, humidity or dampness.

Do not subject the equipment to shocks or strong vibrations.

Keep hot soldering irons or guns away from the equipment.

Allow  the  equipment  to  stabilize  at  room  temperature  before  taking  up  measurement  (important  for

exact measurements).

Do  not  input  values  over  the  maximum  range  of  each  measurement  to  avoid  damages  of  the

instrument.

Use  caution  when  working  with  voltages  above  35V  DC  or  25V  AC.  These  Voltages  pose  shock

hazard.

-118- 

Summary of Contents for 1190






















































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands