Peak Pilates MVe Reformer Mat Set Assembly & User'S Manual Download Page 2

2

Peak Pilates 

strongly

 recommends consulting a physician for a complete medical exam before beginning any exercise program. 

Having a complete medical exam is particularly important if the user has a family history of high blood pressure, has heart 
disease, is over the age of 45, smokes, has high cholesterol, is obese, or has not exercised regularly in the past year.

If at any time while exercising the user feels faintness, dizziness, pain, or shortness of breath, he or she must stop immediately.

Important: 

This manual contains important safety and usage information. Before beginning to exercise, read the entire manual 

paying specific attention to all cautions and warnings and obtain qualified instruction on the use of the Peak Pilates MVe  
Reformer and Tower. Use only for the intended exercises. 

Do not

 modify the machine in any way. 

Modifying the machine will  

nullify your warranty.

 Keep this guide handy for future reference.

WARNING: 

Unsafe or improper use of this equipment resulting from failure to read and comply with all requirements and  

warnings could result in serious injury. Because Peak Pilates cannot anticipate every situation and condition that can occur 
while using the MVe Reformer and Tower, we make no representation concerning the safety of this equipment.

There are risks associated with the use of any exercise equipment. The user assumes all responsibility for those risks.

Safety Statement
 

 

 

 

It is the responsibility of the purchaser of the products to instruct all individuals, whether they are end users or supervising 
personnel, on the proper use of the equipment.

Inspect the machine including all structural and mechanical components, hardware, springs and accessories before use. 

Do not

 

exercise on the machine if signs of excessive wear, loose hardware, or other defects are evident. 

Do not

 attempt to fix a defective 

machine. Instead, notify Peak Pilates immediately.

Do not

 remove labels for any reason. They contain important information. If the labels are illegible or missing, contact your 

service representative for replacements.

NOTE: We strongly recommend that all users of Peak Pilates exercise equipment be informed of the following information prior to use:

Proper Use 

 

 

 

 

 

This equipment is only to be used as described by the manufacturer. It is imperative that the MVe Reformer with Tower be used properly 
to avoid injury or damage to the unit. Use only components provided by the manufacturer. 

Do not

 use parts or accessories or 

modify the machine in any way not approved by Peak Pilates. Keep a three foot area (about one meter) around the equipment 
clear of obstructions. Make sure the machine is used on a level surface.

Specific Operating Warnings

Be certain that all hardware is fully tightened before beginning to exercise. 

• 

Verify that no gaps between the coils or other defects are evident in the Springs. If any defects are seen, the Spring/Springs 

• 

must be immediately replaced. 
Verify that no tears or excessive wear are evident in the ropes, foot strap, or double loops. If excessive wear is evident, the 

• 

ropes, strap, or loops must be immediately replaced. 

Recommended Use  

MVe_Tower_Owners_Manual-10_09.indd   2

12/4/09   4:21:16 PM

Summary of Contents for MVe Reformer Mat Set




















Reviews: