manualshive.com logo in svg

Pavone Sistemi JBX8 LCD, Technical Manual

Share
Download
Pavone Sistemi JBX8 LCD Technical Manual Download Page 52

 TABLE RELATING TO THE CODING OF THE STATUS REGISTER

Bit

15

14

13

12

11

10

9

8

Description

Setup

(***)

Weight 

delta

Output 2 Output 1

Input 2

Input 1

Run 

Backup

Hold 

function

Bit

7

6

5

4

3

2

1

0

Description

Not 

calibrated

Weight 

error

Over-load

Under-

load

Tare 

entered

Zero 

band

Peso 

stabile

Centro di 

zero

TABLE RELATING TO THE CODING OF THE KEYBOARD BLOCK

Bit

15-4

3

2

1

0

Description

Not used

 SET key 

enables

FUN 

key enables

—>0<— 

key enables

PRG 

key enables

TABLE RELATING TO THE CODING OF THE DIGITAL INPUTS/OUTPUTS

Bit

15-2

1

0

Description

Not used

IN/OUT 2 enables

IN/OUT 1 

enables

TABLE RELATING TO THE CODING OF THE DIVISION AND DECIMAL VALUES

Address

Description

Accepted values

1101

Division value

1 - 2 - 5 - 10 - 20 - 50

1102

Number of decimals

0 - 1 - 2 - 3 - 4

TABELE RELATED TO THE CODING OF THE COMMAND REGISTER / DATA REGISTER

Register value

COMMAND REGISTER FUNCTION

DATA REGISTER FUNCTION

0x0001

Semi-automatic zero

-

0x0002

Automatic tare

-

0x0003

Cancel peak

-

0x0004

Zero calibration (**)

-

0x0005

Sample weight calibration (**)

Sample weight value in MSB and LSB

0x0006

Analog test

Value between 0 and 100 in intervals of 10 

in LSB

0x0007

Saving data in permanent memory

-

0x000A

Command to weigh

-

0x000B

Switching command from gross to net weight

-

0x000C

Switching command from net to gross weight

-

0x000D

Capture of zero signal (table calibration)

-

0x3FFF

Enabling the Output Data Area reading (*)

-

(*) This command must be sent each time the registers are changed in the Fieldbus Output Data Area, in order that 

the changes are effective in the device. Caution. When the device is switched on, the Output Data Area is completely 

zeroed, so the Fieldbus master must read the parameter values from the Input Data Area and copy them to the relevant 

Output Data Area registers, before sending the reading enabling command 0x3FFF to the Command Register. Other-

wise, all the parameters managed in the Output Data Area would be reset. Do not use in case of CANopen fieldbus.
(**) Function available only in the case of FREE operation or in case of METRIC operation with enabled calibration jumper.
(***) The device is in the setup phase (TRUE flag during access to the SETUP menu of the device).

Summary of Contents for JBX8 LCD






















































Reviews:

No comments

Brands by name

Popular brands

Load more brands