background image

15

Windload  Information

Windload Imposed at 125 mph

Force on Front of Dish - 6,250 lbs

Force on Back of Dish- 3,400 lbs

Torque at Base of Mount-  42,000 ft.lbs.

Overturning moment-  44,000 ft.lbs.

Stress of 6” schedule 40 pipe - 49,233 psi
Stress of 6” schedule 80 pipe - 34,302 psi

Note: For Windloads of 100 mph or more, we recommend using schedule

80 pipe filled with concrete

                                          125mph             50mph

 

Force on Front of Dish-               ,200 lbs           510 lbs

Force on Back of Dish-               1,900 lbs           00 lbs

Torque at Base of mount-            2,760 ftlbs         00 ftlbs

Overturning Moment-                  29,00 ftlbs       4,425 ftlbs

 

Windload  Information

Windload Imposed at 125 mph

Force on Front of Dish - 6,250 lbs

Force on Back of Dish- 3,400 lbs

Torque at Base of Mount-  42,000 ft.lbs.

Overturning moment-  44,000 ft.lbs.

Stress of 6” schedule 40 pipe - 49,233 psi
Stress of 6” schedule 80 pipe - 34,302 psi

Note: For Windloads of 100 mph or more, we recommend using schedule

80 pipe filled with concrete

Summary of Contents for 2.4m Offset Antenna





















Reviews: