background image

25

24

Preparing Phastool

®

 for Installation

Phastool

®

 - Vice Mounted

When Phastite does not need to be assembled in-situ it is recommended that the Phastools’ supplied vice plates are 
used to mount the tool securely in a bench vice.
This assembly process supports both Phastool® 3A and Phastool® 3B
1. Locate supplied vice plate (1 of 2) onto the tool (Figure 23).
2. Each vice plate has two mounting holes.
3. Install the retaining cap screws to secure the vice plate to the tool and repeat for vice plate 2 of 2 (Figure 24).

Figure 19

Figure 23

Quick and easy interchangeable tooling inserts allows the 
Phastool

®

 to install connectors from sizes 1/4” to 5/8”. The 

insert selected is determined by the type of connector to be 
used and the size of the tubing. All inserts are etched with the 
part number and are color coded.
The two inserts are installed on the moving side of the tool 
and the fixed side of the tool (Figure 26). 
1.   One insert is installed on the moving jaw side of the hand 

tool (Figure 26). This is the side closest to the hand tool 
- hose interface.

2.   The other insert is installed on the fixed jaw side (Figure 

26). The fixed jaw is opposite the hand tool - hose 
interface.

Selecting Phastool

®

 Inserts

Phastool

®

 3A - Portable

When operating the Phastool 3A by hand it can be used in any orientation, however it is recommended that the 
supplied boot is used.
1. Place and slide supplied boot onto the tool (Figure 19).
2. The boot has four mounting holes - two on each side. 
3. Install the retaining screws to secure the boot to the tool using a 3mm Allen key (Figure 20).

Phastool

®

 3B - Portable

When operating the Phastool 3B by hand it can be used in any orientation, however it is recommended that the 
supplied handles are used.
1. Locate supplied handle (1 of 2) onto the tool (Figure 21).
2. Each handle has two mounting holes.
3. Install the retaining screws to secure the handle to the tool and repeat for handle 2 of 2 (Figure 22).

Figure 20

Figure 22

Figure 21

Figure 24

Installing Inserts on the Phastool

®

1.  If the hand tool is being picked up, do not pick it up by 

the hose. This will damage the fitting to hose interface.

2.  Ensure the jaws and inserts are free from damage or 

foreign objects.

3.  Correct insert orientation is essential to correct assembly 

of Phastite

®

 connectors, ensure that the dimples are 

orientated left and right (not up and down) (Figure 25).

4.  For all inserts except the SHAPES, ensure that the tube 

slot is orientated upwards (Figure 25).

5.  The inserts slot in and out of Phastool

®

 3A and Phastool

®

 

3B, and click into place (Figure 26).

Figure 25

Phastool

®

 Insert/Fitting Table

Fixed 

Jaw

Style

Moving 

Jaw

B

B

Shapes

A

Shapes

A

A

A

A

A

n

E

D

Tube
O.D.

Bore

ØE

D

B

C

A

F A/F

A

B

n

F

n

E

C

D

Bore

Tube

O.D

.

Table 19

Figure 26

Summary of Contents for Phastite PH-10-4N-TMS




































Reviews: