background image

Easy Start Guide

7. How to operate the Inverter from the keypad

Page 7

This guide has been produced by The Inverter Drive Supermarket Ltd.
All content, including but not limited to graphics, text and procedures copyright

The Inverter

Drive Supermarket and must not be reproduced or altered without prior written permission.

©

The green key will start the motor. The display will reset to 0.00 and
increase as the motor accelerates. The time taken for the motor to
accelerate to the desired speed (in seconds) is proportional to
parameter F114. The “RUN” indicator will illuminate to indicate that the
motor is running. To change the speed whilst the motor is running, use
the up and down keys.

7.3 Press the green “RUN” key to start the motor.

Note: When running, the “M” key can be used to cycle through
other values such as motor rpm, current (A) and voltage (U).

Parker AC10 Series Inverter (to 22kW)

7.1 Select the speed reference.

Press the “M” key repeatedly until the speed reference is shown - the
“Frq” lamp will illuminate. The default is 50.00 (Hz). All digits will
flash except the currently-selected digit. It is the digit that is not
flashing that can be changed.

Note: Once the value is changed it is saved automatically. There
is no need to “save” the value.

Use the “0" (stop) key to move between digits. Use the up and down
arrow keys to change the value as required.

7.2 Set the desired speed.

The “E” key can be used to return the selection to the right-
most digit.

7.4 Press the red “Stop” key to stop the motor.

The red key will stop the motor. The time taken (in seconds) to stop the
motor is proportional to parameter F115.

Once the motor is stopped, the run lamp will not be illuminated and the
display will return to the flashing setpoint shown in 7.2 (above).

Summary of Contents for AC10 series
















Reviews: