ParaZero SafeAir M-600 Pro Installation Manual Download Page 5 | Manualshive

Page: 5 / 23

background image

SafeAir™ M-600 Pro Installation Guide

5

www.parazero.com

1.2

Technical Specifications

The SafeAir™ M-600 Pro system should only be operated in open air and in normal weather
conditions. Error! Reference source not found. describes the technical specifications of the
ystem.

Technical Specifications

Criterion

Specification

Expected Reaction Time

Up to 50ms

Altitude loss until full deployment (hover)

7-10m

Vertical speed of descent (hover):* maximum
takeoff weight between 10.5-15.5Kg

3.6-4.8m/s

Temperature Range

-25°C to + 55°C

Maximum Wind Speed/Flight Speed

55knots

Humidity

95%

*ISA, at zero wind and stabilized vertical speed.

«
...
3
4
5
6
7
...
»

Summary of Contents for SafeAir M-600 Pro
























Reviews:

No comments

Related manuals for SafeAir M-600 Pro

Speedglas 9100 Series

Brand: 3M Pages: 64

Brand: 3M Pages: 2

Speedglas 9002NC

Brand: 3M Pages: 52

Speedglas 9100 FX Series

Brand: 3M Pages: 2

Brand: Dakota Digital Pages: 2

Brand: Dakota Digital Pages: 7

Brand: Dakota Alert Pages: 2

Brand: Labelmate Pages: 2

Brand: SALSA Pages: 2

BEA LZR-WIDESCAN

Brand: Halma Pages: 12

Brand: IFO Pages: 12

Brand: Uebler Pages: 18

Brand: BAFANG Pages: 9

Brand: Fantec Pages: 5

Brand: pleasant hearth Pages: 52

Brand: Walkera Pages: 22

Brand: 4 tec SENSORTECHNOLOGY Pages: 5

Brand: CAME Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands