manualshive.com logo in svg

Paradyne FrameSaver SLV 9626, Installation Manual, Page: 24 / 36

Share
Download
Paradyne FrameSaver SLV 9626 Installation Manual Download Page 24

24

Connecting to the DTE (Router or FRAD)

Procedure

1.

Connect one end of the DTE’s V.35 cable to the data port. 

2.

Plug the other end of the cable into the DTE.

3.

Tighten the screws on each side of the connector to secure them.

4.

Verify that the Port OK LED is on. If it is, the port is set up correctly and is 
operational. If not, make sure both ends of the cable are properly seated and 
secured. Then, check the DTE; RTS or DTR could be down on the DTE.

5.

Check Health and Status messages in the left column of the System and Test 
Status screen for messages.

Main Menu

→

Status

→

System and Test Status

—

If 

System Operational

 appears, the port interface is set up correctly and is 

operational.

—

If not, refer to 

Status Information in the FrameSaver SLV Operations Guide.

NOTE:

When any error conditions are detected, a status message appears along the 
bottom right corner of the screen.

POWER

COM

DBM

MDM

NET

99-16480

DTE

Summary of Contents for FrameSaver SLV 9626





































Reviews:

No comments