Paradyne FrameSaver SLV 9626 Installation Manual Download Page 10 | Manualshive

Page: 10 / 36

Paradyne FrameSaver SLV 9626 Installation Manual Download Page 10

10

About the Installation Procedures

There are two methods for installing and setting up the FrameSaver unit.

One person can install and set up the unit. If this is the case, see

Full Installation

and Setup

.

An installer can physically install and set up access to the unit, and the network
operation center (NOC) can complete the setup. If this is the case, see

Minimal

Installation for Service Providers

on page 13.

Certain procedures are common to both the full installation and minimal methods. These
procedures (starting with

Setting Up Local Management at the Central Site

on page 15)

are referenced in the full and minimal installation instructions. Refer to them, as needed.

Full Installation and Setup

An Easy Install screen is provided to simplify installation and setup. The Easy Install
feature can be used for the first part of the installation when one person is installing and
setting up the unit from beginning to end.

Easy Install Screen Example

main/easy_install 9626

Device Name: Node A 12/26/2002 23:32

EASY INSTALL

Service Type Frame Relay

Node IP Address: 000.000.000.000 Clear

Node Subnet Mask: 000.000.000.000 Clear

TS Access: DLCI 980

Create a Dedicated Network Management Link

Network1 DDS Line Rate (Kbps): Initialize From Network

Network Initiated DCLB: V.54 & ANSI

DSU Latching Loopback (64CC): Enable

Require DSU Latching Loopback Preamble Enable

---------------------------------------------------------------------------

Ctrl-a to access these functions, ESC for previous menu MainMenu Exit

Save

«
...
8
9
10
11
12
...
»

Summary of Contents for FrameSaver SLV 9626





































Reviews:

No comments