Paradyne AIM24000 Installation Instructions Manual Download Page 6 | Manualshive

Page: 6 / 24

background image

6

May

2005

AIM2-A2-GZ40-20

2. With the AIM24000 Printed Circuit Board (PCB) facing up and the AIM24000

faceplate model name on the right, align the edges of the PCB with the slot
module guides on both sides.

3. Slide the AIM24000 into the chassis until it is fully seated. Do not use

excessive force.

4. Tighten the fastening screws on the AIM24000 faceplate. Do not over-tighten

the fastening screws.

Verifying Power

If you have not already powered up your BLC, do so now.

The PWR (power) LED on the AIM24000 faceplate illuminates solid green to
indicate the AIM24000 is receiving power.

«
...
4
5
6
7
8
...
»

Summary of Contents for AIM24000

























Reviews:

No comments

Related manuals for AIM24000

LevelMaster 7100

Brand: ABB Pages: 28

Ability Smart Sensor

Brand: ABB Pages: 4

Brand: ABB Pages: 20

Audio Interface Conectiv

Brand: M-Audio Pages: 18

Brand: Saful Pages: 7

Brand: Juniper Pages: 502

Brand: Datasensor Pages: 4

Brand: Winsen Pages: 6

TUFFScreen 8x8 Fungo

Brand: Beacon Athletics Pages: 6

Brand: ORELL Pages: 28

Brand: PCB Piezotronics Pages: 9

AERASGARD RFTF-C02

Brand: S+S Regeltechnik Pages: 16

Propelling Pencil

Brand: Yard O Led Pages: 12

Brand: Velleman Pages: 23

ADSL2+ Wireless MIMO Router

Brand: Ace Pages: 64

Brand: Hamlet Pages: 122

Brand: Agilent Technologies Pages: 35

Brand: CalAmp Pages: 115

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands