Paradyne AIM24000 Installation Instructions Manual Download Page 11 | Manualshive

Page: 11 / 24

background image

AIM2-A2-GZ40-20

May 2005

11

4. Screw the right side of the RJ21 cable connector into the jackscrew on the

right side of the RJ21 connector frame on the chassis.

NOTE: If you are using a 120 or 180 degree cable, fasten both the top and the
bottom of the RJ21 cable connector to the connector frame on the chassis
using the captive screws.

ADSL Remote Connection

A single line connection can be established between any port on the AIM24000
and any compatible G.lite, ADSL, ADSL2, or ADSL2+ modem.

«
...
9
10
11
12
13
...
»

Summary of Contents for AIM24000

























Reviews:

No comments

Related manuals for AIM24000

Brand: Panasonic Pages: 6

Brand: Panasonic Pages: 3

ECONAVI CZ-CENSC1

Brand: Panasonic Pages: 8

Brand: Panasonic Pages: 9

AR42P9W - Plasma Panel anti-glare Filter

Brand: Panasonic Pages: 5

Brand: Bang & Olufsen Pages: 12

Brand: Yamaha Pages: 33

Brand: Yamaha Pages: 17

Brand: Lindy Pages: 4

Brand: S+S Regeltechnik Pages: 16

Brand: Alpha Arsenal Pages: 15

Brand: Suunto Pages: 5

Brand: Eiko Pages: 21

Brand: JETI model Pages: 7

Brand: NETGEAR Pages: 2

Brand: Macsense Pages: 13

RealPort Ethernet 10/100

Brand: Xircom Pages: 30

Brand: San Jamar Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands