background image

Digiplex LED Keypads 9

3.2.2 Decimal Programming

Section 

[006]

 is programmed using “Decimal Programming”. In this

method, any digit from 000 to 255 can be entered.

3.2.3 Level Programming

Section 

[009] 

is programmed using “Level Programming”. In this

section only one option can be enabled. To enable the option use
the  and  buttons until the option you want is illuminated
then press

 

the 

[

ENTER

]

 button to set the option

.

3.2.4 WinLoad Programming

With the 

WinLoad Security System Management Software, 

the

Digiplex

 control panels and keypads can be programmed

remotely through a modem at 300 baud or on-site at 19,200
baud with a 

306 Adapter

.  For more information refer to the

WinLoad On-Line Help

.

3.3 M

ODULE

 B

ROADCAST

The Digiplex Control Panel’s 

Module Broadcast

 feature can be

used to copy the contents of one LED Keypad model to one or
many other LED Keypads of the same model. For example, the
programming of a 20-zone LED Keypad can be copied to many
other 20-Zone LED Keypads.

Step 1: From 

Normal Mode

 press and hold the

 [0] 

button.

Step 2: Enter

 [

INSTALLER

 

CODE

]

.

Step 3: Enter section 

[954]

.

Summary of Contents for Digiplex DGP-620



























Reviews: