background image

Digiplex LED Keypads 21

Warranty

The Seller warrants its products to be free from defects in
materials and workmanship under normal use for a period of
one year (unless otherwise indicated). Except as specifically
stated herein, all express or implied warranties whatsoever,
statutory or otherwise, including without limitation, any implied
warranty of merchantability and fitness for a particular purpose,
are expressly excluded. Because Seller does not install or
connect the products and because the products may be used
in conjunction with products not manufactured by Seller, Seller
cannot guarantee the performance of the security system.
Seller obligation and liability under this warranty is expressly
limited to repairing or replacing, at Seller's option, any product
not meeting the specifications. In no event shall the Seller be
liable to the buyer or any other person for any loss or damages
whether direct or indirect or consequential or incidental,
including without limitation, any damages for lost profits, stolen
goods, or claims by any other party caused by defective goods
or otherwise arising from the improper, incorrect or otherwise
faulty installation or use of the merchandise sold.

Summary of Contents for Digiplex DGP-620



























Reviews: