13
> No Sub”. This sets the soundbar to reproduce the
entire frequency range when playing content.
Wired Subwoofer Connection
Using a high-quality RCA style cable designed for
subwoofer connection, connect “Sub Out” from the
soundbar to the “LFE In/Sub In” on the subwoofer.
Use the soundbar’s menu system and choose
‘Subwoofer > Wired Sub’.
Reference your subwoofer’s manual to learn how to
properly adjust the sub’s level and phase controls
to achieve proper blending with the soundbar. The
subwoofer’s crossover should be set to “bypass”,
“LFE”. For subwoofers that do not have a “bypass”
or “LFE” crossover setting, we recommend adjusting
the crossover to its highest setting.
Wireless Subwoofer Connection
Press the subwoofer’s sync button and hold for 3
seconds. The subwoofer’s LED will blink quickly.
Use the soundbar’s menu system and choose ‘SUB
> WIRELS > SYNC’. The soundbar will display ‘PSH.
BTN’ [PUSH BUTTON].
If pairing has completed successfully, the subwoofer’s
LED will stop blinking and remain on and the sound-
bar will display ‘SYNCED’. Please note: If a link is not
established after 30 seconds, the subwoofer’s LED
will start blinking slowly and the soundbar will display
‘FAILED’. Repeat if syncing fails.
Reference your subwoofer’s manual to learn how to
properly adjust the sub’s level and phase controls.
The subwoofer’s crossover should be set to “bypass”
or “LFE”. For subwoofers that do not have a
“bypass” or “LFE” crossover setting, we recommend
adjusting the crossover to its highest setting.
Please note: The subwoofer wireless transmitter built
in to your Paradigm PW SOUNDBAR is not compatible
with Paradigm’s subwoofers with built in subwoofer
wireless transmitter technology. You can still utilize
wireless functionality by connecting the included
subwoofer wireless receiver to the LFE input on your
subwoofer or connecting a Paradigm PT-1 or PT-2
transmitter to the Sub Out on the soundbar.
Please note: If you decide to no longer use wireless,
turn off the soundbar’s wireless transmitter by using
the menu system and choosing ‘SUB > WIRELS >
TRN.OFF’ [TURN OFF] or ‘SUB > NO SUB’. Doing this
will turn off the transmitter and automatically set the
soundbar for no sub.
WARNING! When operating wirelessly, the subwoofer
may be susceptible to RF interference in the 2.4GHz
bandwidth from microwave ovens and wireless devices
such as Wi-Fi systems, video game consoles, cordless
telephones, Bluetooth devices, and baby monitors.
Generally, this issue (intermittent sound or slight pop-
ping noises) is easily resolved by physically separating
problematic devices from one another—a distance as
little as two feet will often alleviate the interference. In
the case of microwave ovens, the interference will only
occur when the microwave is operating.
Using a Paradigm Subwoofer
When configuring your subwoofer we recommend
beginning with the following settings:
Low-pass: Bypass
Phase: 0°
Volume: Knob set to vertical (12-o’clock to
1-o’clock position).
IR OUTPUT
These jacks accept IR emitters with 3.5mm mono-
style connectors. One IR emitter is included with
the soundbar. Plug the IR emitter into either of the
soundbar’s IR Out jacks and place the other end of the
IR emitter over the IR sensor on anther piece of equip-
ment. The use of an IR emitter allows the soundbar to
pass IR signals from any remote control to a tethered
device—allowing control of equipment in locations a
remote would not normally reach.
Summary of Contents for PWSOUNDBAR
Page 1: ...OWNER S MANUAL ...
Page 41: ...40 NOTES ...
Page 42: ...41 NOTES ...
Page 43: ...MANUEL D UTILISATION ...
