background image

Fold speed:    

 

Max 7000 sheets/h

 

Paper size: 

 

   

 

B6(182 x 128mm) US 5" x 7"  - A3(420x297mm) US11" x 17" 

 

 

 

 

 

Paper weight:

 

 

 

50—200 gsm Bond: 16 to 50# Text: 40 to 135#

 

Paper stack capacity:  

500 sheets, 64gsm Bond: 500 sheets 18# bond

 

Dimensions:

 

   

 

1240 x 550 x 464 mm  (49" x 21.7" x 18.3")

 

Weight:

 

 

 

 

48 Kg (106 lbs.)

 

Troubleshooting 

Error Messages

MESSAGE

Cause

Solution

No Paper

Stack paper of feed tray

PAPER ERR

A jam has occured or other 

error

Press C.  Clean sensor if 

needed

OVERLOAD

Motor is overloaded

Turn off, then on.

Troubleshooting

Problem

Cause

solution

Machine won't turn on No power to machine

Check power cord and outlet

Machine on but won't 

start 

Paper has not reached the 

guide plate of the paper 

feed table.

Push in the paper until its lead 

edge touches the guide plate.

Fold plates are not in or a paper 

jam has occurred 

Remove and replace fold 

plates. Remove any jam.  

Internal problem

Call your dealer.

When the start button is 

pressed, the paper feed 

wheels rotate but no 

paper is fed.

The paper feed table has been 

lowered.

Lower the paper set lever to raise 

the paper feed table.

The paper has not been 

fanned well.

Fan the paper well

The paper is curled

Straighten the paper curl.

Page                                                                                                                                                 2019     

14

Summary of Contents for PF-34 M

















Reviews: