Panasonic Windea VGDT18143W, Simple Manual

Page: 57 / 118

Touch of the security circuit to
change, select one of "Off/30sec./60sec./
120sec./300sec.", and touch
108 109
Touch when wrong number is entered.
All the numbers are erased.
Touch
2
Touch the
numeric buttons
1
Touch
2
3
Imitation
Sound
Notification sound is sounded.
When security is turned on: Beep
When door closure security is on: Beeps
When security is turned off: Short beeps
Sound message is played.
When security is turned on: Security has
been turned on.
When door closure security is on: Beep,
Check that all windows and doors are locked.
When security is turned off: Security has
been turned off.
Voice
(Initial setting)
Off No message or notification sound is sounded.
Select one of "Voice/Imitation Sound/
Off", and touch
To set the sound played in the door phone, set in "External Security Door Phone Sound".
( Page 109)
●
This setting is available when set to "Permit changes to delay setting: Yes" with the installation setting.
(Consult with the management company or the company that installed the system.)
●
"Security Alarm Delay" does not appear when set to "Permit changes to delay setting: No".
Security Off Sound screen
Security Off Sound
Enter the 4 digit security number
1
Touch
2
Touch
any one
1
Touch
2
Touch
any one
1
3
60sec. It will go into security vigilance state approximately
60 seconds after setting the security.
It will go into security vigilance state immediately
after setting the security.
Off
120sec. It will go into security vigilance state approximately
120 seconds after setting the security.
30sec. It will go into security vigilance state approximately
30 seconds after setting the security.
300sec. It will go into security vigilance state approximately
300 seconds after setting the security.
Security Alarm Delay screen
Security Alarm Delay
● Security number is set.
● Returns to the Security Setting screen.
Initial setting
Security 1/Security 3/Security 4: Off
Security 2: 60 sec.
Set the security number in the following
procedure when
is touched
INTRODUCTION
USUAL USAGE
SETTING ACCORDING TO
YOUR PREFERENCES
OPERATIONS AND MEASURES
WHEN ALARM GOES OFF
SECURITY ALARM SETTING
AND DISARMING
RECORD
MANAGEMENT
OTHER
Setting According to Your Preferences
Note
Note
Note
Note
Note
Note
Note
●
When entered as 1234
●
This setting is available when set to "Permit changes to delay setting: Yes" with the installation setting.
(Consult with the management company or the company that installed the system.)
●
"Security Preliminary Alarm" does not appear when set to "Permit changes to delay setting: No".
3
Security alarm is immediately sounded when the door
is opened while security alarm is set.
Off
Security Preliminary Alarm screen
An installation setting is required to disarm security vigilance with the external security set switch.
(Consult with the management company or the company that installed the system.)
External Security Door Phone Sound
Security Preliminary Alarm
Touch
2
Door Phone Sound screen
Touch
2
Touch
any one
1
3
Imitation
Sound
Notification sound is sounded from the unit entrance (door phone).
When security is turned on: Beep
When door closure security is on: Beeps
When security is turned off: Short beeps
Sound message is played from the unit entrance (door phone).
When security is turned on: Security has been turned on.
When door closure security is on: Beep, Check that all windows
and doors are locked.
When security is turned off: Security has been turned off.
Voice
(Initial setting)
Off
No message or notification sound is sounded
from the unit entrance (door phone).
Off
(Initial setting)
The Living mode is not changed even
when the external security is set.
Sets the living mode automatically to "Absence mode"
when the external security setting is performed.
On
Absence Mode By Security screen
Touch
2
Touch
any one
1
Select one of "Voice/Imitation Sound/
Off", and touch
Absence Mode By Security
3
Select either of "On/Off", and touch
Initial setting
Security 1/Security 3/Security 4: Off
Security 2: 60 sec.
This setting is available when set to "Living mode: On" and "Circuit setting: External security" with the installation setting.
(Consult with the management company or the company that installed the system.)
Changing the setting of the security setting
for the Absence mode is not available.
Touch of the security circuit to change,
select one of "Off/30sec./60sec./120sec./
300sec.", and touch
Touch
any one
1
Touch
any one
Touch
any one
30sec.
Security preliminary alarm is sounded for approximately
30 seconds when the door is opened when security
vigilance is set, then security alarm is sounded.
60sec.
Security preliminary alarm is sounded for approximately
60 seconds when the door is opened when security
vigilance is set, then security alarm is sounded.
120sec.
Security preliminary alarm is sounded for approximately
120 seconds when the door is opened when security
vigilance is set, then security alarm is sounded.
300sec.
Security preliminary alarm is sounded for approximately
300 seconds when the door is opened when security
vigilance is set, then security alarm is sounded.