Panasonic WH-SXC09D3E5 Service Manual Download Page 43

Page: 43 / 128

12.1.5. Cool + Tank Mode Operation

12.1.6. Tank Mode Operation

Control contents:

• 3 ways valve direction

- 3 ways valve switch and fix to tank side.

• Heat Pump Thermostat characteristic

- Water set temperature = tank set temperature or

[55 C]

whichever lower.

- Heat Pump Water Outlet set temperature is set to Maximum (53 C) at tank mode

i. Case 1

- THERMO OFF TEMP:

1. THERMO OFF TEMP = Water set tempe

[+2 C]

2. Tank temperature > THERMO OFF TEMP for continuous 3 minutes, heat pump OFF and water pump OFF.

- THERMO ON TEMP:

1. THERMO ON TEMP = Water set tempe

[-3 C]

2. When detect tank temperature < THERMO ON TEMP, water pump ON for 3 minute then heat pump ON.

- Pump ON when Tank temperature is less than Tank temperature when Heat Pump Thermo Off -

[-3 C]

Summary of Contents for WH-SXC09D3E5

































































































































Search results

Summary of Contents for WH-SXC09D3E5

Reviews:

Related manuals for WH-SXC09D3E5

Brands by name

Popular brands

Panasonic WH-SXC09D3E5, Service Manual

Search results

Summary of Contents for WH-SXC09D3E5

Reviews:

Related manuals for WH-SXC09D3E5

Brands by name

Popular brands