Music
Codec
File extension
Restrictions
MP3
.mp3
–
NOTE
•
Some fi les may not be played back even if they fulfi l these conditions.
•
Do not use two-byte characters or other special codes for data.
•
Th
e device may become unusable with this TV if the fi le or folder names are changed.
Stereo / Bilingual Sound Selection
When you receive the stereo / bilingual sound system, sound output modes can be selected
by pressing the Sound Selection button.
Audio Signal
STEREO
MAIN I
SUB II
MONO
Mode
Indicator
NICAM
.......Used in New Zealand, Singapore, Hong Kong, etc.
Type of
broadcast
Regular broadcast
(Standard Audio)
R
NICAM MONO I
(MAIN I )
NICAM
STEREO
NICAM DUAL
MONO
(MAIN I / SUB II )
Mode
Indicator
No
Indicator
I
II
A2 (German)
.......Used in Australia, Malaysia, etc.
Type of
broadcast
Regular broadcast
(Standard Audio)
BILINGUAL or DUAL MONO:
MAIN I / SUB II
STEREO
Mode
Indicator
No
Indicator
•
If the stereo signal is poor or the receiving conditions are not optimum or if STEREO:MONO
automatic switching occurs, it is recommended you switch from STEREO to MONO.
•
Even when the contents of the receiving signal undergo changes, selection mode is kept intact.
•
When the receiving conditions deteriorate, listening will be easier if the mode is set to the
MONO position, using the Sound Selection button.
•
DUAL, also known as DUAL MONO or as BILINGUAL is not currently transmitted in some
countries.
FAQs
Before requesting service or assistance, please follow these simple guides to resolve the
problem. If problem still persists, please contact your local Panasonic dealer.
White spots or shadow images (noise)
•
Check the position, direction, and connection
of the aerial.
•
Keep the space between the TV and RF cable.
Neither image nor sound is produced
•
Is the TV in “AV mode”?
•
Is the mains lead plugged into the socket outlet?
•
Is the TV turned On?
•
Check [Picture Menu] and volume.
•
Check all required cables and connections are
firmly in place.
An error message appears
•
Follow the message’s instructions.
•
If the problem persists, contact your local
Panasonic dealer.
There may be red spots, blue spots, green
spots and black spots on the screen
•
This is a characteristic of liquid crystal panels
and is not a problem. The liquid crystal panel is
built with very high precision technology giving
you fine picture details. Occasionally, a few non-
active pixels may appear on the screen as a fixed
point of red, green, blue or black.
Please note this does not affect the performance
of your LCD and it is not a quality problem.
The LCD panel moves slightly when it is
pushed with a finger
Clattered sound might be heard
•
There are some looseness around the panel to
prevent damage to the panel.
The panel might move slightly when it is pushed
with a finger, and clattered sound might be
heard. This is not a malfunction.
TV goes into “Standby mode”
•
Auto power standby function is activated.
•
The TV enters Standby mode about 30 minutes
after broadcasting ends.
No sound is produced
•
Is “Sound Mute” active?
•
Is the volume set to the minimum?
The remote control does not work or is
intermittent
•
Are the batteries installed correctly?
•
Has the TV been switched On?
•
Point the remote control directly at the front of
the TV (within a 30 degree angle of the front of
the TV).
•
Situate the TV away from sunshine or other
sources of bright light not to shine on the TV’s
remote control signal receiver.
Sound is unusual
•
Set the sound setting of the connected equipment
to “2ch L.PCM”.
•
Check the [HDMI Input] setting in the Sound
Menu.
•
If digital sound connection has a problem, select
analogue sound connection.
Sound level is low or sound is distorted
•
Sound signal reception may be deteriorated.
•
Set [MPX] in the Sound Menu to [Mono].
Pictures from external equipment are unusual
when the equipment is connected via HDMI
•
Is the HDMI cable connected properly?
•
Turn Off the TV and equipment, then turn them
On again.
•
Check an input signal from the equipment.
•
Use an equipment compliant with
EIA/CEA-861/861B.
No image can be displayed
•
Is [Colour] or [Contrast] in the Picture Menu set
to the minimum?
Blurry or distorted image
(no sound or low volume)
•
Reset channel.
Chaotic image, noisy
•
Change the setting of [P-NR] in the Picture
Menu (to remove noise).
•
Check nearby electrical products (car,
motorcycle, fluorescent lamp).
Unusual image is displayed
•
Turn off the TV Mains power, then turn it on
again.
15
TH-L32XM5KMTX_fold_EN.indd 15
TH-L32XM5KMTX_fold_EN.indd 15
6/1/2012 8:26:18 AM
6/1/2012 8:26:18 AM
