ー 19 ー
ー 20 ー
●
Do not modify the Tro-Reel HS in any way.
Otherwise, electric shock, fire or damage due to falling of equipment may occur.
●
Do not use where exposure occurs.
Otherwise, electric shock, fire or damage due to falling of equipment may occur.
●
Use at ambient temperature -10 ℃ ~ 40 ℃. If you use outside this temperature range, please contact Panasonic Corporation.
●
Install this product according to the construction rules in Electrical Equipment Technical Standards .
Especially for the primary side of power supply of the duct, use an adequate over-current breaker.
●
Installation must be carried out correctly according to this Installation/Operation Manual included with the products.
Improper installation may result in electric shock, fire or damage due to equipment falling.
■
Before assembling, be sure to read through this Operation / Installation Manual for correct assembly.
■
The work must be performed by a qualified engineer.
■
After setup
、
Please pass this Operation Manual / Installation Manual to the customer.
Installation of the High-Tro-Reel must be performed only by a licensed electrician. To prevent injury or accidents, always pay attention
to the following points.
Precautions on installation
●
This product is for general indoor use only. Do not use this product for a damp place, a place where corrosive gas is generated
or a place where cutting oil is directly splashed.
Electric shock, fire or damage due to equipment falling may occur.
●
Position the opening of a unit facing downward or sideways. If installed with the opening facing upward, a unit may produce
sparks, causing fire, poor contact or separation of collector arms from wires.
●
When damage and crack occurred in the insulating sheath of the duct, please change the duct.
Otherwise sparking may occur, causing fire, poor contact, or derailing of the trolley, etc.
●
When mounting the duct to the hanger, stuff a duct into a hanger not to pinch a hand.
Observe may cause injury to your fingers.
●
When remove the duct from the joiners, pull it out while holding the tip of the duct. so that the duct may not jump out from
Joyner.
Observe, damage to the ducts, may cause injury.
●
When filing the ends of the duct, use protective gear such as glasses.
Otherwise, your finger may be injured.
●
Be sure to remove burrs using file after cutting, drilling.
Observe may cause injury to your fingers.
●
Use products only within the specified rating and load capacity.
Violation of specified ranges may cause burning or fire.
●
Firmly fix this product to the material of construction and construct it.
Otherwise, fire or damage due to falling of equipment may occur.
●
Construct the material of construction that installs the product firmly.
Otherwise, damage due to falling of equipment may occur.
Warning
Caution
Tro-Reel HS Installation Manual
〈
Non-Tension Type
〉
Maintenance schedule of Tro-Reel HS（Non -Tension Type)
Please check by the maintenance table based on this maintenance schedule.
Refer to the maintenance table for a concrete check item.
At introduction The 5th year
The 10th year
Maintenance done by the electrical work trader.
The product-life is different in use conditions and the service space, however, It is possible to use it for about t 10 years
by regularly maintaining and the regular service in correct construction.
・Check the presence of remarkable dirt of the surface of the conductor.
(Once every 3 to 6 months) → Clean it with the cotton waste etc.
・ Check the Tro-Reel unit doesn't become it in a zigzag line.
(Once every 3 to 6 months) →Review the size between conductors in the joint.
・Check the Tro-Reel unit is not away from the hanger.
(Once every 3 to 6 months) →Install the Tro-Reel unit on thehanger.
・Check whether there is not crack and a lack of the insulation sheath
(Once every 3 to 6 months)
→Product exchange recommendation that exchanges the Tro-Reel unit.
Tro-Reel HS unit
・Check whether there is loosening of the fixation screw or the terminal screw.
(Once every 3 to 6 months) →Retighten.
・Check whether the resin has not been damaged. (Once every 3 to 6 months)
→Exchange products.
Joiner
Center feed-in joiner
・Check whether there is loosening of the nut. (Once every 3 to 6 months) →Retighten.
・Check whether the resin has not been damaged. (Once every 3 to 6 months)
→Exchange products.
Hanger
Guide cap
Insulating piece
・Check whether there is loosening of the bolt. (Once every 1 to 3 months) →Retighten.
・Check whether wear has reached the replacement line. (Once every 1 to 3 months)
→Exchange the collector, when worn out to the replacement line.
・Check damage of spring pin and rotation axis, wear-out of metal fittings of spring receiving.
(Once every 1 to 3 months)→Exchange products when damage or abnormality is found. Please keep normal.
Collector arm
Product exchange recommendation.
